0
you use a spanner to open a rusted nut bolt because you need a strong tool to open a rusted nut bolt.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
How you remove a fan clutch from a 04 envoy xuv?
Buy a spanner wrench with studs on the face to hold the pulley and a open end wrench that fits @ the fan bolt at auto parts store. Then turn the fan bolt in the direction the fan turns when the engine is on, holding the pulley with spanner wrench. And its off. Not that hard.Stan
Why is long spammer used to open rusted nut?
The longer spanner gives you a greater "mechanical advantage". If you search for "The six simple machines" there are loads of excellent explanations... you can think of the spanner as a either lever with the pivot point (or fulcrum) at one end, or as a single spoke from a wheel (where the nut is the middle of the wheel). Work is a force acting over a distance. Work (Joules) = Force (Newtons) x Distance (metres). Your muscles have a fixed maximum output of work... by using a longer spanner you are making the distance longer, so the amount of force needed to get the work done at the end you pull on gets smaller.
Serpentine belt removal of a 1995 Lexus gs300?
first remove the viscus fan off the water pump mark it up first so the holes go on the same studs they came off. looking on the front of the engine there is a light alloy tensioner that has a smooth face round the pulley, there is a 14 or 15m bolt head on this. What you need to do is put a ring spanner on this bolt and then pull it clockwise { it is very hard to move with just a spanner } What I do is fit the ring spanner on the bolt head then get a socket and extension bar on the open end of the spanner to give extra leverage. Once there is enough slack on the belt remove it off the pulleys. Refitting is the same as removal I find it easier to put it on the alternator last.
What is a crescent wrench used for?
It is an adjustable spanner, an open ended spanner with a movable jaw allowing it to fit various sizes of nuts and bolts.
What are open bolt-submachine guns?
an open bolt gun is simply a gun that fires from an open bolt, the only time the bolt is closed is during the firing and when the firing is stopped the bolt remains open. many open bolt guns have an integral firing pin machined directly on the bolt examples of open bolt guns: uzi mac Thompson 1928
What is a spanner can you ues a 32 open end wrench?
Spanner is the British term for wrench. Your second question doesn't make sense, please re-write it and try again-
How do you open an ignition barrel for a freightliner truck?
you use a spanner or screwdriver you then use minimal force to open it this way you will be able to use it again
How do you remove the bolt on the Winchester 69a?
Open the bolt, hold the trigger back, pull the bolt out
How do you open sump plug on vauxhall zafira 1.6 petrol and what type of spanner you need?
Its a M14 star bit
What is AF screw thread?
To the best of my knowledge, there is no such thing as an 'AF screw thread'. AF actually stands for 'Across Flats', and is the measurement term for the width of certain spanners jaws. A 7/16" AF spanner for example measures 7/16" across the jaws. AF spanners were designed to fit several older type of screw threaded bolts, such as BSW, BSF and others. A 7/16 AF spanner will fit both a 3/16 BSW and 1/4 BSF bolt. You can of course find spanners with BSW measurements on them, however, a 3/16 BSW spanner indicates that the threaded part of the bolt is 3/16" in diameter, the actual size across the jaws of the spanner is as described above, 7/16", which mirrors the size of the hexagonal head of the bolt measured across the flats, this principle is essentially the same when dealing with BSF. The whole subject of screw threads (particularly the older ones) is quite a minefield, but I hope this brief explanation is of some help! Mikesk AF simply means across flats.So the size marked on the spanner is the distance between the flats of an open end spanner or the opposing sides of the nut or bolt it fits.BSW,BSF and BA spanners and sockets are not AF as such as the size stamped on them is the size of the threaded part of the bolt or nut they fit. There is a comparison chart for the different standards in imperial and metric on the web site Baconsdozen which explains how to identify the different threads etc.
In club penguin mission 1 how do you fix the telescope?
You must open your gadget phone and click the red button, 3 items will come out, a comb, scissors and a spanner, click the spanner, then click the telescope . :) thanks for your time
How do you remove the headlight assembly on a 1992 Mazda mx3?
There is a bolt behind the bumper (next to the horn) which has to be removed. You need to partially remove the bumper on the side you're working on to get to it. I found that with a rachet spanner, it was possible to bend the bumper back a bit to get to it. I didn't replace the bolt when I fitted the new headlamp!! Other than that, remove the obvious bolts that you can see when the bonnet's open and the lamp connections...
