0
Will a 9mm ruger p89 barrel fit in a 90 slide or must you use the 89 slide also?
Wiki User
∙ 15y ago
Two different calibers, two different slides, do not mix and match.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
What are the specifications of a Ruger GP100?
The weight of a Ruger GP100 must be 2.2 pounds, 76mm barrel length, and is double action. It has a range of 55-110 yards, and can be a 6-shot or 7-shot gun.
What is the easiest way to cut down a gun barrel?
Take it to a gunsmith- who will also know how long the barrel must be to be legal.
How do you takeout old ignition lock?
look at the column around the ignition lock their is a set screw you must loosen and lock along with barrel will slide rite out.
Is it dangerous to shorten a gun barrel?
It can be, depending on the action the gun uses. It can also be illegal if you cut the barrel length below the legal limit. In the US, a Title 1 rifle must have a minimum barrel length of 16 inches, and a Title I shotgun must have a minimum barrel length of 18 inches.
How do you break down a smith and Wesson 659?
First, double check to make sure the pistol is unloaded (both magazine removed and chamber empty). Cock hammer. Retract slide enough to align the circular end of the slide stop (located above serial number) with the notch in the slide. Push the slide stop out from the other side of the pistol, and remove it from the frame. Pull slide forward and off frame. Next, with the slide upside down, carefully remove the guide rod and recoil spring. Next, twist the barrel bushing (the piece on the front of the slide that keeps the barrel in place) counter clockwise and pull forward out of slide. Then remove barrel from slide. Assembly is in reverse order. Be careful putting the recoil spring/guide rod back on, as it rests on a tiny notch in the barrel and can easily slip and shoot across the room (fast enough to break a window or put your eye out). Another point of interest are the ejector and other "levers" that stick up from the frame, you must hold these down when putting the slide back on the frame. Good luck and enjoy your 659. I sure like mine!
Why must you dry your slide before putting it on the stage of the microscope?
because of liquids on the slide or to clean the slide
What is the basic unit of PowerPoint?
The slide. There must be at least one in a presentation.
Under what circumstances is a Crate and Barrel coupon code unusable?
Crate and Barrel coupon codes are unusable under two main circumstances. They are, if the coupon has expired and also if the coupon has already been redeemed. The code must also be valid.
What is a Ruger single action revolver?
Type of handgun made by the Ruger company. The hammer must be cocked before each shot. Just pulling the trigger without cocking the gun does nothing.
What is a barrel racer?
A barrel racer is a person who engages in barrel racing - a race in which a horse must be ridden around standing barrels.
How far must you pull the slide back for the locking slide of a Glock 17 pistol to disengage from the slide?
Only a few millimeters are necessary to free the slide from the lock.
How do you disassemble a erma werke ep .25 hand gun?
WARNING!! WEAPON MUST BE FULLY UNLOADED!! remove clip, remove all ammo from clip, pull slide and visually look into feed and assure that weapon is not loaded. reinstall empty clip, pull triger and dry fire weapon to release sping tension. pull two sided lever pin above the trigerguard (two side pin is above triger and just forward) with thumb and forefinger down into the trigerguard area then push the slide forward being careful and slow looking out for spring and spring guide(that they do not pop out),slide forward untill you have separated the two,(frame and the slide). to remove barrel from slide, push barrel forward while holding slide and carefully pull barrel up and out of slide. to re-install it use a bic pen hold the tip of pen in through slide point slightly up and into the end of the barrel slowly guide and install the barrel in reverse as when removing.(push barrell in all the way out of slide, to assure that spring is in correctly. to install the slide back into the frame, install the spring guide into the spring with small pionty tip to the rear and the spring into the firing pin, and as one unit (that can be pushed together) put the small tip of the spring guide into the rear of the frame into the hole that is recessed into the slide guide (that is built as part of the frame),push firing pin into spring to lock with triger release,it has to stay attached to frame,pull lever pin and install the slide, and slowly push slide into the firing pin you may need to turn slightly the firing pin so that the slide will go back in place ,release the lever pin when the slide is all the way in place.
