0
You have 16 pin obd with 3456712y16 pin out what can you do for change to obd2?
Wiki User
∙ 15y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What is the name of the plug you test for your engine light?
I think you are referring to the Universal OBD (or OBD2) test port. This is the plug under the dash that you plug the OBD code tester into. It may also be referred to as the 16-Pin Data Link Connector (DLC).
Is the onboard diagnostic computer on your v6 1196 Eddie Bauer explorer obd obd2 or obd3?
It is OBD2. OBD3 is not out yet, and the OBD2 was REQUIRED in 1996. Ford actually started using OBD2 in 1994 even though not yet required. You can always look for the 16 pin DLC on the drivers side of the vehicle somewere around the underside of the dashboard, usually about knee hight. Obd vehicles the connector could be anywere and have any shape, and amount of pins but are usually located in fender, under the hood. I hope this answers you question.
Where is the obd2 port of 1999 proton wira?
Below the steering wheel. It will have 16-pin but not OBD2 compliant. You will need an adapter to convert the to OBD2. The engine (presumably) Mitsubishi 4G15 Efi which originally 12-pin. Proton did not use 12-pin but maintain the 16-pin where 4 pins are not used.
What are the pin locations on your 2000 Dodge Durango obd2 connector?
Pin 1 is upper left. Pin 16 is lower right. They are numbered in order. OBD-II is a government standard, all the connectors are the same, regardless of make/model. OBD-II is not used by shorting pins together and watching the 'check engine' light flash, you have to use an OBD-II reader, available at your local auto parts store. If this question is in reference to the location of the OBD-II connector jack in the 1999 Dodge Durango, it is located under the drivers side dash, just left of the hood release.
1996 Maxima gxe obd1 or obd2?
All cars and light trucks built and sold in the United States after January 1, 1996 were required to be OBD II equipped. In general, this means all 1996 model year cars and light trucks are compliant, even if built in late 1995. However there is no guarentee your 1996 is OBD2. Some early 1996 Nissan Maxima's were OBD1 and later models were OBD2. The OBD2 connector is a 16 pin connector and is almost always located on the driver's side under the dash.
Where is the OBD connector on a 2000 Dodge Durango?
The OBD plug is a sixteen pin connector under the dash on the driver side.
Can anyone let you know the OBD pinouts for a 1995 Jeep Cherokee?
Depending on if it is a MY95 or MY96 will determine if it is OBD2 or not. If it is MY05 it has a 6 pin connector near the PCM that pins out as follows:1= ground2=N/C3=data Transmit4=Data Recieve5=ignition6=not used
Where is the data link connector located on the 95 Concorde 3.5 engine?
It is a 6 pin (may be blue or black) rectangle under the dash on the driver side.It is not OBD 2 so it is not the normal 16 pin connector.It is a 6 pin (may be blue or black) rectangle under the dash on the driver side.It is not OBD 2 so it is not the normal 16 pin connector.
Which terminals are jumpered on the OBD(6 pins) connector on a 1996 Ford Thunderbird (pre OBD2)for DTC retrieval?
The OBD-II specification was made mandatory for all cars manufactured in the United States to be sold in the United States for the model year 1996. A Ford 1995 model year would have the 6 pin EEC IV DDL connector. Jump pins marked "D" and "F" for code retrieval.
i want to change my pin number?
changing my pin number
What scanner can you use to read data and codes for a 2006 ford LCF?
you need to use something with a 9 pin deutche connector because the 20 pin obd2 port will not allow communications.
Where do you find the obd on a citreon relay van?
Citroen relay pre 05 have a 3 pin connector coming out of wiring loom next to ecu which is under bonnet passenger side , use code reader with a fiat 3 pin connector . Launch and snap on read them ok. 05 onwards have 16 pin obd in dash just under steering wheel .
