0
If your washing machine will agitate, but refuses to spin out, you more than likely have a bad lid switch. A lid switch, when working properly, tells the washing machine when the lid is closed, thus allowing the washer to spin out. A faulty switch will signal that the lid is still open, even though it isn't, and the water will not spin out. Repairing a lid switch is easy for the average do-it-yourself person with some instructions from internet sources, especially videos. These switches will run anywhere from $20-$60 depending on the machine and are found at your local appliance repair centers.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
What do you do when your washing machine is done a load of laundry but still full of water?
The pump may be bad or weak. You can check the small lid switch under the lid. When you close the lid...it will engage. These will sometimes get out of sinc with the lid and not engage.
Kenmore washing machine will fill with water and drain off but will not spin water out or wash?
If a Maytag washer fills with water but does not agitate it could a problem with the switch in the lid. There is a switch that locks the lid down during agitation and spinning. The magnet could be defective.
What did a washing machine look like in the 1920s?
1920's washing machines didn't have a lid. You would have to get the hose from the garden and fill the washer machine up!
Have model kaws750jqo machine fills and starts washing then quits when it should go to rinse and sometimes have to lift lid to start washer again?
There is a safety switch on all washers and dryers to stop accidents. It turns off power when the lid is raised. Most likely the switch needs adjustment if the machine goes into normal cycle when you lift the lid. Locate switch and adjust to make it less sensitive. First turn power off, remove plug.
Where is the serial number on a washing machine?
There should be a tag under the lid on the rim of the opening.
Why wont Kenmore washing machine spin?
The wig-wag or spin actuator or belt is faulty. -Simple problem for someone experienced in washing machines.
How do you fix my kirkland signature washing machine that won't drain?
It sounds like a lid switch to me. i just don't know what a Kirkland signature machine is like, but all machines have some kind of switch to make it turn on And when they go out your machine will not drain. Go to Youtube and see if they have that type and they will show you how to fix it step by step. It's free
What would cause a washing machine not to agitate or spin?
either the lid switch is bad or the transmission is faulty. The Whirlpool and their subsidiaries brand(s) are well known for faulty or broken lid switches which break from the users either dropping or slamming their lids. The weight combined with force,breaks the switch and will keep them from agitating,draining or spinning.
When do you load the clothes into washing machine?
Okay people, here is how you load a washing machine, *Turn the washing machine on, *Put the recommended amount of detergent in, *put your clothes in - unfold and turn clothing inside out - do not overfill the machine *close the lid. DONE!!! Another This is my procedure for a top loading machine: Turn on, add appropriate amount of soap powder/detergent, start water until powder dissolves, add laundry then continue water to fill, close lid & start wash/rinse cycle.
How do you change a washing machine filter?
Washing machine filters are cleaned not changed unless they are broken, they are usually inside above the wash bin, check the instructions inside the lid or your owners manual for the location of yours.
How do you stop washing machine from moving during spin cycle?
It is moving because an unbalanced load makes the machine vibrate and "walk " when it is on the spin cycle. Stop the machine, open the lid. You will find more clothes on one side. Redistribute the clothes evenly around the washer, close lid, restart.
What is the difference between a regular washer and a front load washer?
Front-load simply means that the washing machine door is on the front face of the washing machine, rather than a lid that lifts from the of the washing machine (top load). One would 'load' the clothes into the washer through the open front, hence the name front-load.
