0
What else can I help you with?
If a metal can is heated with the lid open and then the lid is replaced and the can is allowed to cool what would happen to the can and why?
If the lid formed a seal, it should sag from the outside pressure.
What do you do when you can't open a jar?
run lid over hot water and open with a cloth over lid.
How many ml in the lid of a soda?
Approximately 7.5ml will fit inside of a lid from a soda. This is the lid that keeps the bottle of soda closed. It would only take about 4 lids to make an ounce.
How should Harriet test the jar lid to determine if it is successful for its intended audience?
Harriet should ask several senior citizens to evaluate whether her jar lid design is easier to use than a traditional jar lid.
Why you do not start into high power on a microscopes?
I am going to ignore your poor grammar skills on this one, but here is the answer. You first start on a low power to locate the specimen or bacteria. Then you switch to a high power to get a better look at it. Hope this helps.
Trunk lid open warning light remains on when the trunk is shut on a 1989 sundance?
open trunk lid and locate the trunk light switch.push switch to see if light goes off. if light does not go off, replace switch. if light does go off, adjust switch to where trunk lid operates switch when trunk is closed
Why is the deck light staying on Chrysler Sebring?
The trunk lid is open or the ajar switch has malfunctioned.The trunk lid is open or the ajar switch has malfunctioned.
Have model kaws750jqo machine fills and starts washing then quits when it should go to rinse and sometimes have to lift lid to start washer again?
There is a safety switch on all washers and dryers to stop accidents. It turns off power when the lid is raised. Most likely the switch needs adjustment if the machine goes into normal cycle when you lift the lid. Locate switch and adjust to make it less sensitive. First turn power off, remove plug.
How to fix lid switch on kitchen-aide washer?
If you are sure the lid safety switch is at fault do not bother with it, they are cheaper and easier to replace
What does dECk mean on 2008 dodge avenger?
The trunk lid is open or the trunk ajar switch has malfunctionedThe trunk lid is open or the trunk ajar switch has malfunctioned
How can I locate the septic tank lid?
To locate the septic tank lid, look for a rectangular or circular area in your yard that is slightly raised or different in texture. You can also use a metal detector or hire a professional to help locate it.
How do you take off the top of a Kenmore 80 series washer to replace the lid switch?
Make sure the unit is unplugged, then used two butter knives to insert in the front part of the lid...about 2 inches in from the outside corners to raise the lid. ANS 2 - Don't risk making your wife mad by ruining the butter knives ! -try two small pry bars or even flat screwdrivers.
Washing Machine Lid Switch Repair?
If your washing machine will agitate, but refuses to spin out, you more than likely have a bad lid switch. A lid switch, when working properly, tells the washing machine when the lid is closed, thus allowing the washer to spin out. A faulty switch will signal that the lid is still open, even though it isn't, and the water will not spin out. Repairing a lid switch is easy for the average do-it-yourself person with some instructions from internet sources, especially videos. These switches will run anywhere from $20-$60 depending on the machine and are found at your local appliance repair centers.
How do you locate a kill switch for a 1986 Nissan pickup?
no such switch.
When you open your laptop and it wakes up How does your laptop know the lid was opened?
there is a small magnet on lid and magnetic switch on laptopbase
Kenmore washing machine will fill with water and drain off but will not spin water out or wash?
If a Maytag washer fills with water but does not agitate it could a problem with the switch in the lid. There is a switch that locks the lid down during agitation and spinning. The magnet could be defective.
Error f35 for Kenmore smart washer?
F35 is a failure of the analog pressure switch. You can get a new one from Repairclinic.com It's an expensive part. Remove the top lid by undoing the three fasteners on the back of the top lid. Pull the lid towards the back and lift up.The pressure switch is a brown module inside a black housing with a black rubber tube connected to it. It is locate on the top right panel towards the rear of the washer. Rotated it 90degrees to free it. Remove the connector and rubber tube to replace.
