answersLogoWhite

0

If you are sure the lid safety switch is At Fault do not bother with it, they are cheaper and easier to replace

User Avatar

Wiki User

15y ago

What else can I help you with?

Related Questions

Ge washer wont spin or drain?

check the lid switch it is under the top of the washer and is usually activated by a pin attached to the lid of the washer


IA Kenmore washer model number 11024822200 will not spin Could this be a belt and how do you fix it?

The Kenmore washer model 11024822200 does not have a belt. If the washer is not spinning, it could be due to issues with the motor, motor coupler, or lid switch. You may need to check these components and repair or replace them as necessary.


Kenmore washing machine will fill with water and drain off but will not spin water out or wash?

If a Maytag washer fills with water but does not agitate it could a problem with the switch in the lid. There is a switch that locks the lid down during agitation and spinning. The magnet could be defective.


Why is my washer agitating but not spinning?

There could be several reasons why your washer is agitating but not spinning. Some common causes include a broken or worn drive belt, a faulty lid switch, or a malfunctioning motor coupling. It is recommended to consult a professional technician to diagnose and fix the issue.


Why is my washer not agitating or spinning properly?

There are several possible reasons why your washer may not be agitating or spinning properly. It could be due to a faulty motor, a broken belt, a malfunctioning lid switch, or a problem with the transmission. It is recommended to consult a professional technician to diagnose and fix the issue.


How do you fix a GE washer that won't spin?

To fix a GE washer that won't spin, first check if the lid is firmly closed, as many models have a safety switch that prevents spinning if the lid is open. Next, ensure the load is balanced; an unbalanced load can cause the washer to stop spinning. Additionally, inspect the drive belt for wear or damage, and examine the drain pump for clogs that may prevent water from draining, as the washer won't spin if it detects water remaining in the drum. If these steps don't resolve the issue, consider consulting the user manual or contacting a professional for further assistance.


How much would it cost to fix a washer that won't spin?

The cost to fix a washer that won't spin typically ranges from $100 to $400, depending on the issue and whether you hire a professional. Common problems might include a faulty lid switch, drive belt, or motor, which can vary in repair costs. If the washer is under warranty, repairs might be covered, reducing your out-of-pocket expenses. Always consider getting a diagnostic first to assess the specific issue.


Washing Machine Lid Switch Repair?

If your washing machine will agitate, but refuses to spin out, you more than likely have a bad lid switch. A lid switch, when working properly, tells the washing machine when the lid is closed, thus allowing the washer to spin out. A faulty switch will signal that the lid is still open, even though it isn't, and the water will not spin out. Repairing a lid switch is easy for the average do-it-yourself person with some instructions from internet sources, especially videos. These switches will run anywhere from $20-$60 depending on the machine and are found at your local appliance repair centers.


Why is my Hotpoint washer not draining properly?

Your Hotpoint washer may not be draining properly due to a clogged drain hose or pump, a malfunctioning pump, or a problem with the lid switch. Check these components to troubleshoot the issue.


Your washing machines filled up with water and quit?

Simplest solution is on the lid. There should be a small plastic pin sticking out that closes a switch when the lid is closed. This shuts the agitator off when you lift the lid. They can come off or break. The switch it closes can go bad also. After that, it could be several things deeper in the washer. If you feel capable of doing it, the switch should be easy to change. Unplug the washer. The switch is right under the edge of the top. Should be one screw holding it in on the edge of the top. Take the screw out, cut the two wires going to it and wire them together. Try the washer. If it works, problem solved. Get a new switch, wire it in. If it doesn't work, put the old switch back and call the repairman.


Where is the lid switch located on a Kenmore washer model?

"Kenmore" is a brand name for Sears, not a manufacturer. Your washer was most likely made for Sears by Whirlpool. You can tell by the first 3 digits of the model number, ie: 110.9764882 would be a Whirlpool since "110" is their manufacturer's code. The lid switch is typically just under the top of the cabinet to the right of the opening where you put the clothes in. There will be a slot there that corresponds with a plunger on the lid itself which actuates the switch below. For more help see www3.sears.com for a complete breakdown of your model.


Why does a washer not drain properly?

A washer may not drain properly due to clogs in the drain hose or pump, a malfunctioning pump, or a faulty lid switch. Regular maintenance and checking for blockages can help prevent drainage issues.