These machines do not have belts. Lid switch is your most probable culprit. Though there are other parts that will stop it from spinning.
There is a clear hose attached to the water level control of the washer. The other end of the hose is attached underneath the washer. The hose isn't attached with any hose clamps so if the washer rocks from a uneven load it could come disconnected and on the next load the water fills up and never stops. Just disconnect the water and electric and the drain and turn the washer on its side look for the hose and reattach it to the hookup underneath-- I just fixed mine, I thought I was going to be buying a new washer but this one still works great now! Hope this helps- Jesse
the following discussion is useful for answering this question: http://ths.gardenweb.com/forums/load/laundry/msg0700323110578.html You can easily and cheaply get rid of the smell by using a product called smelly washer, go to smellywasher.com
Most Kenmore gas dryers do not have a traditional pilot light. Instead, they use an igniter to light the gas burner when needed. If your Kenmore gas dryer is not heating, it could be due to a faulty igniter or other heating element.
A regular clothes washer typically uses around 7-15 amps during operation. It may vary slightly depending on the specific model and brand of the washer.
The issue could be a clogged sprayer nozzle, a faulty washer pump, or a broken washer fluid line. Check the nozzle for any debris blocking the flow, listen for the sound of the washer pump when trying to spray, and inspect the washer fluid lines for leaks or breaks. If necessary, clean or replace the nozzle, pump, or lines as needed.
There could be several reasons why your Kenmore washer is not starting. Some common issues include a faulty power supply, a malfunctioning door latch, a broken timer or control panel, or a problem with the motor. It is recommended to check these components and consult the user manual for troubleshooting steps or contact a professional technician for further assistance.
If a Maytag washer fills with water but does not agitate it could a problem with the switch in the lid. There is a switch that locks the lid down during agitation and spinning. The magnet could be defective.
There could be several reasons why your Kenmore Elite washer won't turn on. Some common causes include a tripped circuit breaker, a faulty power cord, a malfunctioning control panel, or a problem with the door latch. It is recommended to check these potential issues and consult the user manual for troubleshooting steps. If the problem persists, contacting a professional technician for further assistance may be necessary.
A good place to go to order replacement Kenmore vacuum parts is online as Sears Parts Direct. They have parts to 3,236 Kenmore Vacuums. You will need the part or model number to get information on the part.
A Venta air washer could be purchased from a number of online retailers. Some examples would be eBay, Amazon, Wayfair, Bed Bath & Beyond, Living Direct and Sears.
There is a clear hose attached to the water level control of the washer. The other end of the hose is attached underneath the washer. The hose isn't attached with any hose clamps so if the washer rocks from a uneven load it could come disconnected and on the next load the water fills up and never stops. Just disconnect the water and electric and the drain and turn the washer on its side look for the hose and reattach it to the hookup underneath-- I just fixed mine, I thought I was going to be buying a new washer but this one still works great now! Hope this helps- Jesse
Reviews for Kenmore humidifiers can be found online at a variety of sites. Reviews can be found on the Kenmore website or a site called consumer reports.
It could be the windscreen washer motor
It could be a problem with the belt. Call Sears and have someone come out to diagnose; it may cost you some money to do that, but at least then you'll know if you need a new machine (or if repairing this one makes sense).
the following discussion is useful for answering this question: http://ths.gardenweb.com/forums/load/laundry/msg0700323110578.html You can easily and cheaply get rid of the smell by using a product called smelly washer, go to smellywasher.com
Kenmore appliance parts can be found at the website sears parts direct, the website has about 200 parts for every model of appliance made by Kenmore you could possibly want.
956451561561566$