0
Trough
What else can I help you with?
What layer has waves?
the top layer because,the bottom of the sea makes waves till it gets to the top
What is a trough and a crest?
it has to do with waves. trough- is the bottom of the wave crest- is the top of the wave
When two waves are in the same place at the same time to combine to produce a single wave?
only if the waves are IN PHASE. This means if you are looking at a diagram of 2 waves going at each other, both waves have to be the same size, wavelength, AND on the same side of the diagram, whether its on the top or bottom. If one wave is on the bottom and the other on top, but has the same size, it will produce a standing wave.
How does a depth finder work?
They use ultra sound waves that are bounced off the bottom of a body of water. Newer depth finders use sonic waves.
How do waves get bigger?
Waves can get bigger due to factors such as increasing wind speeds, longer distances over which the wind blows, or when waves encounter a change in bottom depth. These factors contribute to the transfer of energy from the wind to the water, causing the waves to grow in size.
When two waves are in the same place at the same time they combine to produce a single wave?
only if the waves are IN PHASE. This means if you are looking at a diagram of 2 waves going at each other, both waves have to be the same size, wavelength, AND on the same side of the diagram, whether its on the top or bottom. If one wave is on the bottom and the other on top, but has the same size, it will produce a standing wave.
Did the salt in Salt Lake City lake settle to the bottom?
no the waves made it mixed up.
How do submarines target underwater objects?
They use Sonar to send sound waves to the bottom of the oceans.
What is a trough in waves?
It is the Lowest point in a wave the upper point is the crest the bottom point is the trough H
What causes a breaking wave?
Waves out in the ocean don't break because they are in deep water, waves break when they reach shallower water and so the bottom of the wave catches on the bottom and causes a bit of friction which slows the wave down and cause it to fall over itself, which is breaking
Surface wave energy reaches all the way to the way to the bottom of the ocean is it true or false?
Ocean waves are a surface effect. The wave breaks and rolls when the bottom is the depth of half total wave height. That is to say, a five-foot wave crest breaks in five feet of water. The water disturbed by the wave is as deep as the wave is tall. The waves rolling onto the beach drain back under the incoming sets of waves and create what is commonly called under-tow. At depths down to about 40 feet, depending on the energy, near the beach, the waves create surge. The surge is a bit disorienting because you are sloshing back and forth one way, the plants another and the bottom is, of course, staying put. The effect that waves have on the bottom is that they produce sand from crashing on rocks and near the beach they deposit that sand in a rippled pattern because of the surge. In the deep ocean, the energy of the waves will have long since been damped out by the water between the waves and the bottom and there will be no appreciable effect. The answer is both true and false, depending on what you are calling the bottom of the ocean. See the diagram in the link below.
What is Phase change recording?
When recording a snare drum with a mic on the top and the bottom, a phenomenon known as phase cancellation can occur. Sound is a wave. A property of waves is that they can interfere with each other destructively and constructively. Imagine the sound waves caused when hitting a snare drum. The waves from the top of the drum will go into the top mic first, then the bottom mic. The waves from the bottom of the drum will go into the bottom mic first then the top mic. Because of the timing of the waves as they arrive at each mic, they will destructively interfere, and many of the frequencies integral to a good snare drum sound will be low in gain (volume). So a good audio engineer will use a phase reversal lead on the bottom mic. This is just like a normal lead, only the positive and negative pins have been reversed, and the phase cancellation will not occur.
