0
Can anyone give you more info on pats for a mk 3 fiesta as you have installed new non pats ignition barrel with key and want to bypass the whole thing forever?
Locate PATS unit, which is usuall located passenger side near the glove box. You will have to have a feel about, but will find it in a metal cage. Unbolt by removing screw (spline type) which is found just inside door post. Once pulled out, open unit. You will see 2 relays which have black covers. Remove covers, and using piceces of plastic, make the contacts permanent, one will be normally closed & one will be normally open. This will allow the fuel pump to run, but in my instance not allow the starter to turn. After investigation, i found that PATS removes the -ve feed to the starter relay. I just provided a new -ve to the relay, and the car now starts 1st time. Only down side is that the red LED falshes for a while before finally going out. Hope his helps... This info is no real use to car theives, as it takes a good couple of hours to get this sorted.
What else can I help you with?
Has anyone got a diagram of ignition barrel wiring for 1987 944s?
no
How do you remove ignition barrel on vt?
The ignition barrel can be removed by removing the retaining ring. The barrel will slide out. Remove the wiring harness from the back of the barrel.
How do you remove fiat stilo ignition barrel?
to remove stilo ignition barrel, look underneath the barrel. there is a square button holding the barrel in. put the key in the ignition, turn 2 notches, and press the button in with a screwdriver. Then wiggle the barrel out using the key.
How do you remove ignition barrel on citroen Picasso?
To remove the ignition barrel on a Citroën Picasso, start by disconnecting the battery to ensure safety. Next, remove any surrounding trim to access the ignition switch assembly. Insert the key and turn it to the "on" position, then locate the release pin or tab on the ignition barrel, which typically needs to be pressed in while pulling out the barrel. Finally, pull the ignition barrel out of the steering column.
How do you replace ignition module in a 98' Malibu?
Remove the ignition module retaining ring. Pull the ignition barrel out. Remove the wiring harness from the back of the ignition barrel. Reverse the process to install the new ignition module.
How do you remove the ignition barrel on a 1992 VN Commodore without using the key?
you need to have the ignition barrel in the on position otherwise you cant to it.
How many hours to fit ignition barrel in x type jag?
how long will it take to fit ignition barrel in x type jag
How do you replace ignition key tumbler in 1999 Chevrolet lumina car?
Remove the ignition retaining ring. Pull the ignition barrel out. Remove the wiring harness from the back of the ignition barrel. Reverse the process to install the new ignition key tumbler.
How do you remove the ignition barrel from a citroen xsara?
To remove the ignition barrel from a Citroën Xsara, first disconnect the vehicle's battery to ensure safety. Then, remove the steering column cover by unscrewing the necessary screws. Insert the key and turn it to the "on" position, which will allow you to press the release button on the ignition barrel. Finally, pull out the ignition barrel gently to remove it from the steering column.
How do you remove ignition barrel on combo van?
To remove the ignition barrel on a Combo van, first disconnect the vehicle's battery to ensure safety. Then, you'll need to remove the steering column cover by unscrewing any screws and gently prying it apart. Insert the ignition key and turn it to the accessory position; locate the release tab or screw on the ignition barrel and press or unscrew it while pulling the barrel out. Once released, you can fully remove the ignition barrel from the steering column.
How do you remove an ignition barrel on a transit?
To remove the ignition barrel on a Ford Transit, start by disconnecting the battery to ensure safety. Then, use a screwdriver to remove the steering column cover and locate the ignition switch. Insert the key and turn it to the "on" position while pressing the release tab on the ignition barrel to remove it from the steering column. Finally, pull the ignition barrel out gently and disconnect any wiring harnesses attached.
How do you wire a citroen saxo ignition barrel?
To wire an ignition barrel in the Citroen Saxo, begin by disconnecting the wire at the negative terminal of the battery. A lead wire has to go to the ACC terminal on the ignition barrel. The starter relay wire goes to the ST terminal and the ignition wire is connected to the IGN terminal.
