0
What else can I help you with?
How do you change a pcv hose on a 2005 MPV Mazda?
The pcv hose is connected to the Pcv valve and the intake manifold. the pcv valve is circular metal piece on the top of the engine cover. Just replace with any rubber hose with similar thickness and heat resistance. You may use same ring clamps if necessary
How do you install an engine block heater on Chevrolet 1996 k1500?
There are several types but generally the best are either the in-line heater hose style or the freeze plug style. If you use the in-line heater hose style, just cut the heater hose, put the block heater in place then make sure the heater control is left on at night. If you use the freeze plug style you'll need to remove an existing freeze plug and put the block heater in it's place. The magnetic style block heaters are not recommended. They seem like a good idea but they're more trouble than they're worth.
Where is PCV valve in a 1990 Lincoln Mark VII LSC?
I have an 89 LSC and the PCV is located at the back of the plenum on the intake manifold. There is a hose coming out of it--pull up on the hose until the pcv comes out or the hose pops off of it----Its a stretch for sure and a flashlight is definitely recommended! there is a wire filter under the pcv. a deck screw taped to the end of a Phillips screwdriver is the best tool to use to remove it for cleaning. when you replace your pcv, clean the wire filter under it. the pcv valve, grommet and wire filter are still available from the dealerships. .
Is there a PCV valve on a 1997 Mercury Villager SE 3.0 FI and where is it located?
it is located at your valve cover driver side on the end of the hose the pcv valve is pluged into the valve cover at the end of the hose you may have to use a screwdriver to pry it out of the hole. is it a straight blk hose the goes to the fuel rail
Does a 2.2 liter 1998 Chevy Cavalier have a PVC valve?
Yes. The PCV valve is attached to the intake by a hose and is located in the valve cover and held by a plastic retainer. Use a pair of pliers to loosen the PCV valve retainer. Unthread the retainer from the valve cover to expose the PCV valve. Pull the PCV valve from the valve cover grommet and remove the valve from the hose.
How do you bypass the heater core of a 1992 Mercedes 190e?
Disconnect the send and return lines from the heater core and use a hose coupling and hose clamps to connect these two lines together
How do you repair heater hose on a Chrysler cirrus?
To repair the heater hose on a Chrysler Cirrus, first, ensure the engine is cool and disconnect the battery. Locate the damaged heater hose, then use a hose clamp to secure a new section of hose if the damage is minor, or replace the entire hose if needed. Cut the old hose off, attach the new hose to the fittings, and secure it with new clamps. Finally, refill the cooling system with coolant and check for leaks.
Can you use pressure to clear out a heater core?
Water pressure from a garden hose is sufficient.
Where is the PCV valve on 2007 Honda CR-V?
Standing in front of the auto, the PCV valve is located on your left. The PCV screws into the intake manifold just above the alternator. 1. Remove the two cap screws (10 mm) to remove the intake manifold cover. 2. Remove the PCV hose using needle nose pliers. 3. Use a 17 mm deep well socket to remove the PCV valve from the intake manifold. 4. Install the new PCV valve, PCV hose and intake manifold cover.
Where is the pcv on a 1992 Nissan maxima?
the pcv is located on the right top side of the valve cover. it has a hose connected directly to the crankcase cover.(on my car the cover is red)it is simple to replace and costs dirt cheap.NEVER open the hose and take off the pcv when hot. use a wescott for simplicity. specs for 1992 Nissan maxima se, single overhead cam, probably the same,different pcv for dohc though.
How do you replace heater hose on Volvo 2000 V70?
To replace the heater hose on a 2000 Volvo V70, first ensure the engine is cool and disconnect the negative battery cable. Locate the heater hose running from the engine to the heater core, then use pliers to loosen the hose clamps and carefully remove the old hose. Install the new hose by securing it with the clamps, making sure it's properly seated, and finally reconnect the battery cable. Check for leaks after running the engine and ensure everything is functioning correctly.
Can you use standard heater hose for 2001 Saturn L200?
No you have to order them because they are specially molded.
