answersLogoWhite

0

KEYLESS ENTRY SYSTEM With the keyless entry keypad, you can: • lock or unlock the vehicle doors without using the key. Your vehicle has a factory set 5 digit code that operates the keyless entry system. You can also program your own 5 digit personal entry code. The factory-set code is located: • on the owner's wallet card in the glove compartment • or at your dealer. When pressing the controls on the keyless entry keypad, press the middle of the controls to ensure a good activation. This system will disable the power door lock controls. These will not work until the vehicle is disarmed. Programming your own personal entry code To program your own code: 5. Enter factory set code (keypad will illuminate when pressed). 6. Press 1/2 control within five seconds of step 1. 7. Enter your personal 5 digit code. Enter each digit within five seconds of previous one. 8. After the code is entered, the locks will cycle, confirming that the new code has been set. Do not set a code that includes five of the same number or presents them in sequential order. Thieves can easily figure out these types of codes. Your personal code does not replace the permanent code that the dealership gave you. You can use either code to unlock your vehicle. If a second personal code is entered, the module will erase the first personal code in favor of the new code. Locks and Security 149 Locks and Security If you wish to erase your personal code, use the following instructions: 1. Enter factory set code. 2. Press 1/2 control and release. The system will now only respond to the factory set code. Anti-scan featureThe anti-scan feature prevents repeated attempts at arriving at a valid key code. The keyless entry pad is disabled for 1 minute after 7 unsuccessful attempts (35 consecutive button presses) at entering a valid key code. The keypad will flash during this 1 minute mode. However, the 7/8 and 9/0 controls will still lock the vehicle. Anti-scan will be turned off after: • one minute of keypad inactivity. • the remote entry transmitter UNLOCK button is pressed. • the ignition is turned to the ON position. Unlocking the doors with the keyless entry system To unlock the driver door, enter either the factory set code or the personal code (each digit must be pressed within five seconds of the prior digit). The interior lamps will also illuminate. To unlock all doors, enter the factory set code or personal code (driver door unlocks) and press the 3/4 control within five seconds. Locking the doors with the keyless entry system It is not necessary to enter the factory or personal code prior to locking all doors. To lock the doors: • with the driver's door closed, press the 7/8 control and the 9/0 control at the same time. Locks and Security 150

User Avatar

Wiki User

17y ago

What else can I help you with?

Related Questions

Can you reset the keyless entry on the driver's door?

Yes, but the specifics depend on the make and model of the car, or the make and model of the after-market keyless entry system.


How to reset keyless entry system on Chevrolet Colorado?

disconnect the negative battery terminal and leave it disconnected for 15 minutes, then reconnect.


Why do your Subaru Outback parking lights begin blinking as soon as you connect the negative terminal of a newly installed battery?

It's the theft part of the keyless entry system...reprogram your keyless entry and it stops... It's your cars keyless entry system that is the source of the problem. If the battery has been disconnected, it will cause this to happen. You have to find the keyless entry system reset button on my 1997 subaru it is under the dash on left side it is a black button hold the button in and at the same time turn the key to the on position (Do not start the car just turn to the on position) for about 20 seconds and it will reset


How do you program a 2004concorde a spare keyless entry?

To program the 2004 Concorde spare keyless entry, you can take the vehicle to the dealer or you can download the manual. In the manual, there are steps to reset the keyless entry using your vehicle's VIN and other identifications.


How do you reset keyless entry on a ford sport trac?

To reset or change the keyless entry on a sport trac, first enter the factory code on the keypad. Press the 1/2 button within 5 seconds. Enter the new code that you wish to use. The doors should lock then unlock, indicating the system is now reset and ready to use.


Where is the factory reset code for keyless entry on 2000 excursion?

There is no factory reset code for keyless entry on a 2000 Ford Excursion. To find the code, locate the module underneath the dashboard. You may need a borescope to look at the number.


How do you reset the keyless receiver on 1992 deville?

To reset the keyless receiver on a 1992 Cadillac DeVille, first, ensure the vehicle is turned off and the key is removed from the ignition. Then, locate the keyless entry module, usually found in the trunk or under the dashboard. Disconnect the module's power connector for about 10 seconds, then reconnect it. Finally, reprogram the keyless entry remotes as needed to complete the reset.


How do you reset key-less entry on 2005 Pontiac Grand Prix?

To reset the keyless entry system on a 2005 Pontiac Grand Prix, first, ensure the vehicle is in the "On" position without starting the engine. Then, press and hold the "Unlock" button on the driver's door while simultaneously pressing the "Lock" button three times. Release the "Unlock" button, and the system should beep, indicating a successful reset. Finally, test the keyless entry remote to ensure it's functioning properly.


Do you have to reset the keyless entry remote on a 2000 Chevy Blazer after you change the batteries?

Try SPASTICPUPPY.NET.


How do you reset keyless entry on a 87 maxima?

I'd check the users manual for the programming guide.


How do you reset Key less entry for Mazda rx8?

To reset the keyless entry system for a Mazda RX-8, start by sitting inside the vehicle and closing all doors. Insert the key into the ignition and turn it to the "On" position without starting the engine. Press the "Lock" button on the key fob, then turn the ignition off and remove the key. Finally, test the key fob to ensure the keyless entry system has been reset. If issues persist, consult your owner's manual or a professional for further assistance.


Where is the reset for the keyless entry system for a 1998 Subaru Forester?

The button is just to the left of the steering column at the lowest point of the dash. It points straight down. --Ken