0
I'm working on that same problem right now. I've traced the wiring and it goes into the cab, passenger side just below the hood level opening. On the other end the wiring goes down to several locations on the passenger side of the engine. It appears to me Toyota built one of those setup's, where in effect, 'you have to take off all the tires to change the spark plugs...'. Not looking forward to the drudgery!
What else can I help you with?
How to Removing starter from 2005 Chevy Colorado?
Remove the throttle body.Remove the battery box.Remove the oil level indicator and tube.Disconnect the brake booster hose (6) from the brake booster.Disconnect the MAP sensor electrical connector (3).Disconnect the MAP sensor wiring harness retainer (4) from the intake manifold (5).Disconnect the PCV dirty air tube (2) from the camshaft cover.Remove the generator.Disconnect the engine wiring harness retainer (1) from the intake manifold (2).Remove the 2 upper bolts securing the engine wiring harness bracket to the intake manifold.Raise and support the vehicle only high enough to access the remaining components through the wheelhouse.Remove the left front wheel.Remove the left front wheelhouse liner. The battery cableThe engine (4, 6)The MAP sensor (5)Disconnect the following wiring harness retainers from the engine wiring harness bracket:Remove the remaining engine wiring harness bracket bolt. Remove the bracket from the engine compartment through the wheelhouse openingRemove the intake manifold bolts.Lower the vehicle.Remove the intake manifold from the cylinder head.Remove the seal from the intake manifold. Discard the seal.Mask off the open ports to the cylinder head, in order to prevent foreign objects from entering the engine.Clean and Inspect the intake manifold.
How do you remove intake manifold on 305?
take all the wiring and hoses loose from the top of the engine, and you might have to remove the valve covers. then just loosen the intake manifold bolts
What do you do to change an EFI car to carburatted?
First of all this is like going back in time. The conversion will depend on they type of EFI you have. If you have a multiport EFI system then you will need to remove the intake manifold and get a carb intake manifold, remove all of the extra sensors, remove the computer, remove the wiring harness. Then you have to purchase a wiring system for your application, purchase and jet a carb and bring your car to a good tuner to tune the vehicle.
Intake Manifold Removal 89 Toyota Truck 22RE?
How to remove intake from 22re motor,when wire harness go threw the middle of it.is there a brake some where i the line?? On my 92 Xtracab Automatic the wiring harness that goes through the intake manifold has no breaks, it plugs into the transmission in 3 different places and has a couple of clips holding the bundle. Climb under the truck and be gentle while unplugging the harness, dont break a plug or damage the wires.
Can you put the supercharger from a 1998 Buick Regal in a 1998 Oldsmobile Intrigue?
If you get the PCM, engine wiring harness, and intake manifold from the Regal also..
How do you change knock sensor on 2004 Xterra?
To change the knock sensor on a 2004 Nissan Xterra, first disconnect the battery and remove the intake manifold for better access. Locate the knock sensor, which is typically positioned on the engine block, and disconnect the wiring harness. Unscrew the old sensor using a socket wrench, then install the new sensor, ensuring it's properly secured. Finally, reconnect the wiring harness, reassemble the intake manifold, and reconnect the battery.
Where is the EGR valve located on a 1996 Mazda Millenia and how do you replace it?
It's attached to the back of the intake manifold, under the bracket that supports the wiring harness.
Where is the harness for the knock sensor on a 97 Nissan Quest?
On a 1997 Nissan Quest, the harness for the knock sensor is typically located on the engine block, near the intake manifold. You may need to remove the intake manifold to access the knock sensor more easily, as it is often positioned underneath it. The wiring harness should be connected to the sensor itself, which is usually found on the side of the engine. Always consult a repair manual for detailed diagrams and procedures specific to your vehicle.
How do you replace a wiring harness on subaru?
To replace a wiring harness on a Subaru, first disconnect the battery and remove any necessary components to access the harness, such as the intake manifold or dashboard. Carefully label and document all connections to ensure proper reinstallation. Remove the old harness by disconnecting connectors and clips, then install the new harness by reversing the removal process, ensuring all connections are secure. Finally, reassemble any components you removed and reconnect the battery before testing the system.
How do you replace VRIS solenoids on 01 Mazda millenia?
To replace the VRIS solenoids on a 2001 Mazda Millenia, first disconnect the battery and remove the intake manifold for better access. Next, locate the solenoids, which are typically mounted on the intake manifold; disconnect the wiring harness and the vacuum lines attached to them. Remove the mounting bolts to take out the old solenoids and install the new ones by reversing the process. Finally, reattach the intake manifold, reconnect the battery, and check for proper operation.
How do you change a knock sensor on a 2003 Toyota Sienna?
To change the knock sensor on a 2003 Toyota Sienna, first disconnect the negative battery terminal to ensure safety. Locate the knock sensor beneath the intake manifold, which may require removing the manifold for easier access. Disconnect the wiring harness from the sensor, then unscrew and remove the old sensor. Install the new sensor, reconnect the wiring, reassemble the intake manifold, and finally reconnect the battery.
Where is the starter on a 1995 Oldsmobile Aurora located?
It is located under the intake manifold it is very easy to replace but it takes a while you have to disconnect the fuel lines remove the throtle body remove the fuel injector wiring harness remove the pcv hose remove the 6 bolts and 4 studs that hold on the intake manifold and lift it up then the starter should be in plain site and all you have to do is unbolt the starter put the new one on and then reverse the beginning steps
