0
1. Dealer-Programming additional Sentry Keys (requires ONE original key)
In situations where only one key is available, keys must be programmed by the dealer via the Secured Access Method. The Secured Access method applies to all vehicles. This method requires the use of a DRBIIIt scan tool and will also require that you have access to the unique four-digit PIN code that was assigned to the original SKIM. The PIN code must be used to enter the Secured Access Mode in the SKIM. This PIN number may be obtained from the vehicle owner, from the original vehicle invoice, or from the DaimlerChrysler Customer Center. Refer to the appropriate diagnostic information for the proper Secured Access method programming procedures.
2. Self-Programming additional Sentry Keys (requires TWO original keys)
"A" through "G" below is a quick summary of the steps that are required for programming.
Quick Steps:
A. Purchase a blank key and have it cut
B. Insert original key #1 into ignition and turn to On
C. Wait 5 seconds and turn key to off
D. Immediately insert original key # 2 into ignition and turn to on
E. Wait 10 seconds for SKIS indicator in dash starts to flash
F. Turn ignition off, insert new blank key and turn ignition back on
G. Once SKIS light stops flashing and turns off, your new key is programmed
What else can I help you with?
What does code p0513 means for jeep Cherokee Laredo 2005?
Basically it means it means you have a invalid skim key and you are going to have to replace the i mobilizer module with new keys and reprogram.
How do you reprogram a 2000 Jeep Grand Cherokee Keyless Entry?
To reprogram a 2000 Jeep Grand Cherokee keyless entry remote, first, insert the key into the ignition and turn it to the "On" position without starting the engine. Within 10 seconds, turn the key to the "Off" position and back to "On" three times, ending in the "On" position. After a chime sounds, press any button on the remote to program it. Repeat this step for additional remotes, then turn the ignition to "Off" to exit programming mode.
Where is the transponder on a Jeep Grand Cherokee?
In the key
Where is the key release button on a 2002 Grand Jeep Cherokee?
No such part on a 2002 Jeep Grand Cherokee.No such part on a 2002 Jeep Grand Cherokee.
How do you program the key fob for the 1999 Jeep Cherokee?
Dealer only on 96+ newer Jeep Grand Cherokee's
How do you reprogram the factory remote starter and alarm on a 93 Jeep Grand Cherokee after the battery has beeen reinstalled?
replace the remote
How do you program the key fob for the 1999 Jeep Grand Cherokee?
Dealer only on 96+ newer Jeep Grand Cherokee's
Does a 1995 Jeep grand Cherokee have a chip in the key?
No.
What the crossed out key light in the dashboard means in the 2000 Jeep Grand Cherokee Laredo?
If it stays on and jeep doesn't start your truck and both keys need to be reprogramed thru the dealer, they are the only one's that can reprogram the keys and computer, short story the jeep is not reading the chip in the keys to let the computer turn on
How do you program a key fob for a 1994 Jeep Grand Cherokee?
I have a jeep 1994 Jeep Grand Cherokee and found this answer on this site under programing a 1995 jeep Grand Cherokee. Its a very good description uses the same FOB.
What to do when the security system on a 1991 Jeep Cherokee will not allow jeep to start and key will not turn in lock to reset system?
If the security system on a 1991 Jeep Cherokee will not allow the jeep to start and the key will not turn in the lock, disconnect the battery for a few minutes. Try the key in the lock with the battery disconnected. If it works the first time, reconnect the battery and the system should be reset. If the key does not work in the lock, reconnect the battery and reprogram the key fob.
Can you reprogram an obd1 replacement pcm on a 1993 Jeep Grand Cherokee?
Any programming that would need done requires a scan tool.
