0
With great difficulty!
have a look at the following link it'll answer everything you need
www.206info.co.uk/ForumsPro/viewtopic/t=26104.html
Go to Peugeot give them your car reg and get a replacement rheostat or control resistor as they are sometimes known for the heater.
Then go home!
Make a nice cup of tea as you will be going a while!
Then get hold of a Torx 20 Screwdriver and a torch.
You will need to take out the Glovebox so you may as well empty it first.
You need to take the cover off the Glovebox open it but don't let it all way down just pull it out while it's still vertical otherwise it doesn't come out.
Then you need to take out the screws behind the Glovebox cover with the T20 screwdriver and also if you look closely there is another screw inside the Glovebox facing upwards, ( I missed that for a while! )
OK once you have taken all of those out you should be able to push the Glovebox down and out there will be some wires attached to the left hand side, detach them taking note of how they go in.
Right Glovebox out!
Now you need to take out the fan blower.
SO what you need to do is stick your torch and head in behind the Glovebox and if you look as if towards the central console but from behind you will see a round looking object with one screw in.
You need to take that screw out and then turn the thing clockwise. ( This will be really really tight so you need to twist hard, it took me a good few attempts )
Once you have dislodged it there is a clip that goes into the top of the fan for the power, you must take that out and then pull the blower out.
Once you have done this you can reach inside the air duct and you will feel the rheostat. Grab hold of it, twist it to unlock it from its place and pull it towards you.
Once you have done that, then just unplug it out of the socket and then plug the new one in, then push it back to where it was and twist it back to lock it into place.
Put the fan back in and plug the wire in making sure you don't get the wire caught in the air duct.
Screw fan screw back in.
Replace Glovebox!
your done!
Will save you over a £100 in labour charges .....................
What else can I help you with?
How do you Change bulb in heater controls on peugeot 206?
dont
Where is the heater blower motor resistor on a Peugeot 206 CC with air conditioning?
In general, the blower motor resistor is located close to the blower motor.
How do you replace heater matrix in peugeot 206?
The heater matrix, in a Peugeot 206, can be replaced by removing the heater core and the hoses. With the heater core removed you can replace it with a new heater core.
Change front head lights on a Peugeot 206?
how two change my front head lights on a peugeot 206
How do you change a front coil spring on a Peugeot 206?
How long does it take to change a front coil spring on a Peugeot 206
How do you change a cambelt on your Peugeot 206 gti 180 05 plate?
When do change cam belt on peugeot 206 180 gti
How do you change the language settings for a Peugeot 206 dashboard display?
how do you change lanuage display setting on peugeot 206 1.4 hdi 2003 model please
What is a similar car to the peugeot 206?
A similar car to the Peugeot 206 is the Peugeot 205 which the Peugeot 206 is modeled after with minor modifications and upgrades from the Peugeot 205 to the Peugeot 206.
How to change wheel bearings on a peugeot 206?
How do I change a wheel bearing
How do you drain the engine oil on a Peugeot 206?
i wanna know the time between the oil change in my car Peugeot 206 model 2004 ?
How do you change Brake pad change on a Peugeot expert?
how to remove and fit rear brake shoes on a peugeot 206 1.1
What mileage to change drive belt in peugeot 206?
The drive belt on a Peugeot 206 should be change in 80,000 miles. Failure to change drive belts at the appropriate time can result in expensive engine failure.
