Under the dash directly above the gas pedal, find the black relay/module that has an upsidedown white label that says "Hamsar". Disconnect the wiring harness that leads to this module. POOF!! no more DRL's. As far as I can tell this affects the DRL's and nothing else.
How do you disable the DRLs on a 2005 Mitsubishi Endeavor?
In the 05+ Escapes, the DRLs are controlled by the Smart Junction Box. You need to take it to the dealership and have them reprogram the SJB. Usually runs an hour of labor. There are no resistors or fuses to pull to disable them, the SJB must be reprogrammed.
The simplest way to disable the DRLs on this vehicle would be to simply press the parking break pedal down JUST a hair. However, you will have to deal with the emergency brake light being on in your cluster panel.
How to disable the DRLs depends on the specific make, model, and year of vehicle you're working on. In some cases it's easy, in some cases it's almost impossible without causing problems. The preponderance of evidence is that DRLs, thoughtfully implemented, do reduce your risk of getting in a crash or hitting a pedestrian or bicyclist. North American regulations permit both good and bad implementations. If you are trying to disable the DRLs preparatory to "converting" your headlamps with an "HID kit", be advised such kits are dangerous and illegal in every single case.
To disable the daytime running lights (DRLs) on a Mazda 6, you can typically use the vehicle's settings menu if available. Alternatively, you may find a fuse related to the DRLs in the fuse box; removing this fuse will disable them. Another option is to consult the owner's manual for specific instructions based on your model year. If you're unsure, it's best to visit a dealership or a qualified mechanic for assistance.
To turn on the daytime running lamps (DRLs) on a 2005 BMW X3, ensure the ignition is in the "on" position. Then, set the headlight switch to the "AUTO" position, which allows the DRLs to activate automatically when the vehicle is in motion. If the DRLs do not turn on, check the vehicle's settings and ensure that the DRL feature is enabled in the vehicle's onboard computer.
To disable the daytime running lights (DRLs) on a 2004 GMC Envoy, you can locate the fuse box, typically found under the dashboard or in the engine compartment. Remove the fuse labeled for the DRLs, which is usually indicated in the owner's manual. Alternatively, you can adjust the settings through the vehicle's headlight switch if it has that capability. Always consult your owner's manual for specific instructions related to your model.
The relay under the dash is either disconnected (a lot of people do this) or it isn't working.
DRLs are activated through fuse 13 (10 amp size) in your fuse housing inside your engine bay. Removing this will deactivate your DRLs. Just be sure to reinstall it if you have an insurance claim (as most insurance companies will give you a discount for DRLs, but will remove your discount if they find the feature disabled).
go through the fuse box you will find a fuse to control that but sometimes it might disable more than just your day glows...I did it to my 95 s-10 apply the parking brake--you can push it in one notch and the daytime lights will go off but you will have the brake light on your panel == Answer== Under the drivers side dash on the right of the steering column is a shiny finned metal box with a wire going in and a wire coming out. This is the voltage reducer for the DRLs. Disconnect the wire coming out and the lights won't work.
To disconnect the daytime running lights (DRLs) on a 2005 Dodge Ram 1500, locate the fuse box under the dashboard on the driver's side. Remove the fuse labeled for the DRLs, which is usually indicated in the fuse diagram on the cover. Alternatively, you can also disconnect the DRL module, typically found near the front of the engine compartment. Always consult the owner's manual for specific fuse locations and instructions.
Check to make sure your parking brake is completely off. Whenever you set the parking brake, there is an electrical connection that shuts off the drls. Look up under the dash on the driver's side where the parkign brake lever is and look at the connections. The only way the DRLs come on is when the parkign brake is completely off. Even one click will keep the DRLs from coming on. Look there for a possible answer.