0
To disconnect the power antenna on a 1989 Firebird, first, ensure the vehicle is turned off and the key is removed. Locate the antenna, which is usually found near the rear fender or trunk area, and disconnect the electrical connector that powers the antenna. You may also need to remove any screws or bolts securing the antenna to the vehicle to fully detach it. Finally, if applicable, disconnect the antenna cable from the radio before completely removing the unit.
What else can I help you with?
How do you replace the antenna on a 1989 Toyota Camry LE Is it a power antenna?
To replace the antenna on a 1989 Toyota Camry LE, first, ensure the car is turned off and disconnect the battery. If it has a power antenna, you may need to remove the interior trim panel to access the antenna's motor and wiring. Unscrew the old antenna from the exterior, disconnect its wiring, then install the new antenna by reversing the steps. Finally, reconnect the battery and test the antenna to ensure it functions properly.
How do you replace the power antenna on a 1989 ford thunderbird located under the right front fender?
To replace the power antenna on a 1989 Ford Thunderbird, first, disconnect the negative battery cable for safety. Then, remove the right front fender's inner liner to access the antenna. Disconnect the power and antenna cable from the old unit, unfasten any mounting screws, and pull the old antenna out. Install the new antenna by reversing the steps, ensuring all connections are secure before reassembling the fender liner and reconnecting the battery.
How do you replace antenna in 1989 260E?
To replace the antenna in a 1989 Mercedes-Benz 260E, first, remove the interior trim panel covering the antenna base. Disconnect the power and coaxial cable from the old antenna, then unscrew it from the mounting bracket. Install the new antenna by reversing the process: secure it to the bracket, reconnect the power and coaxial cables, and replace the trim panel. Ensure everything is properly connected and test the antenna for functionality.
You want to disconnect the power to the Power antenna on a 1989 caprice classic How do you do this?
There is a wire which connects the power to the antenna. The wire is located under the hood right near the back of the fender hump on the passengers side. If you look you will see where it goes down insdie the fender to the antenna power unit. Just unplag the connector and you are good to go. vbdenny
Which power antanna was used on a 1989 Cutlass Supreme?
Check your RPO codes. If it has an U75 than it had a power antenna. If it has RPO code US6 it has a painted fixed antenna. There was only one style power antenna used from the factory.
Where is antenna relay location on a 1989 Corvette convertable?
where is the radio antenna relay located in a 1989 Corvette Convertible
How to unplug old antenna to replace with standard antenna?
"How to unplug old antenna to replace with standard antenna on 1989 SunDance
How do you disable or repair a power antenna on a 1989 cutlass?
Thankfully mine just died in the up position. Replacing them is a bear. 1. Turn the steering wheel to the far left position. 2. Disconnect the negative cable from your battery. 3. Remove the right inner fender splash shield (4 plastic studs, 3 screws) 4. Remove Phillips head screw retaining the antenna to the fender 5. Disconnect antenna lead and motor wires 6. Remove the two bolts from the lower bracket 7. Carefully pull the antenna and wiring assembly doen through the wheel opening
What is the firing order for a 1989 Pontiac Firebird?
123456
Will a 1989 firebird transmission mount up in a 1991 firebird?
If they are both Chevy V8 cars it will bolt up.
Will parts off of a 1989 Pontiac firebird work on a 1991 Pontiac firebird?
What parts??? Body, engine, suspension???
1989 cutslas and the power antenna motor keeps running and the antenna is stuck in the up position What do you do?
If the antenna is in the up position, you have 2 options, replace the entire assembly, or unplug it. In the trunk under the antenna, you will find a set of 3 wires going into a relay. Unplug those, and the motor will turn off.
