answersLogoWhite

0

To retrieve engine codes for a 1993 Eagle Talon using the key, turn the ignition key to the "ON" position (without starting the engine) and then back to "OFF" three times in quick succession. After the third time, leave the key in the "ON" position. The engine codes will then display in the form of a series of flashes from the check engine light on the dashboard. Each series of flashes corresponds to a specific code, which can be referenced in a service manual for interpretation.

User Avatar

AnswerBot

5mo ago

What else can I help you with?

Related Questions

How do you retrieve fault codes from a 1990 eagle talon?

To retrieve fault codes from a 1990 Eagle Talon, you need to use the On-Board Diagnostics (OBD) connector under the driver's side dash. Jump the appropriate terminals (usually the "TE1" and "E1" terminals) in the diagnostic connector using a wire or paperclip. Then, turn the ignition key to the "ON" position without starting the engine; the check engine light will blink the fault codes in a sequence. Count the blinks to determine the specific codes, which can be referenced in a repair manual for diagnosis.


How do you know if the EGR valve for 95 eagle talon is bad?

check engine light will come on turne the car off turn the key on off on off on within 5 seconds it will flash codes in pulses put these together to make two digit codes look the codes up on the internet or get a haynes repair manual the codes are also the same for first gen neons as well and the key trick.


How do you obtain a new key for your 1991 eagle talon?

write down the vin and take it to a key maker


What is the anti-thief code for a 97 Eagle Talon you changed the head gasket now you need the code?

Ragistration key of anti thief


Is there a key on the dollar bill?

Yes, there is a key on the dollar bill, specifically on the back of the U.S. $1 bill. It is part of the design of the Great Seal of the United States, which features an eagle holding a key in its left talon. This key symbolizes the power of the federal government and the importance of security and protection.


Is there a way to test for engine codes using the gear shift and the key in a 1996 Dodge Intrepid?

yes tun the key from off to ignitiont that's just before it starts the engine 3 times then look at the odomiter it will give you codes


How do you check the engine codes on a Plymouth sundance?

cycle the key three times and count the blinks of the check engine light


Does the 1995 jeep need to be running to read OBD codes?

No but, the ignition has to be on (KOEO, Key On Engine Off).


How do you access check engine codes on a 1994 intrepid?

turn the key on then off 2 times then turn on and check engine light will flash your codes. if you need to know what they are e-mail me rein16502666@yahoo.com I will send them to you.


What does it mean to cycle the key 3 times on a sebring?

turn the key from the off position to the on position without starting the car 3 times, finishing with the key in the on position but without the engine running. this enables the check engine light to display any engine fault codes.


What are the symptoms of a bad camshaft position sensor in a 1998 Dodge Intrepid?

The Check Engine Light should be on if the sensor is faulty. The car may or may not hesitate, stall, or accelerate poorly. To read the engine error codes, cycle the ignition key from "off" to "on" three times: Turn the iginition key to the "on" position where the check engine light comes on but do not start the car. Turn the ignition key to off, then on, off, and on again and leave the key there. The odometer will read out any error codes. P0340 and P0344 are trouble codes for the camshaft position sensor.


Can you turn the key back n forth to get the engine codes to a 1999 Dodge Intrepid?

OBDII vehicles are not programed to allow this feature anymore..since 1996 to present..scanners only... well i just turned the key off and on 3 times and it shows on the display at odmeter some codes, which i had to buy a book to understand what they mean I thought that you were referring to the Check Engine Light flashing the codes. What codes did you receive on the odometer?