0
What else can I help you with?
2000 Ford Windstar coolant leak above thermostat - Does the crossover coolant tube screw in or or just plug in to the manifold?
The crossover tube has an O ring at the end, it is plugged into the intake manifold and held in place by 2 screws. See pictures here: http://leckemby.net/windstar/windstar01.html
How do you remove the coolant crossover tube on a 1993 Lincoln mark viii?
To remove the coolant crossover tube on a 1993 Lincoln Mark VIII, first ensure the engine is cool and disconnect the negative battery cable. Drain the coolant and remove any components obstructing access, such as the intake manifold if necessary. Unscrew the bolts securing the crossover tube and carefully lift it out, making sure to replace any gaskets as needed during reinstallation to prevent leaks.
Where exactly is orifice tube located in 1995 ford windstar?
In a 1995 Ford Windstar, the orifice tube is located in the liquid line of the air conditioning system. Specifically, it is found between the condenser and the evaporator, typically near the firewall. To access it, you'll need to remove the A/C lines connected to the tube.
Do I have to cut the line to remove the orifice tube on my 2003 Dodge Ram?
You could, but you will have to buy a new line to get a new orifice tube.
How do you replace the knock sensor 2001 mercury villager?
BEFORE YOU DO THIS: Be aware that if you are doing it because of a a knock sensor code, it is most like uneccesary. A knock sensor is a passive device that has no effect on normal engine operation. Mercury Villagers are notorious for throwing knock sensor codes when nothing is in fact wrong with the knock sensor (which produces no current under normal conditions). Because of the way emission components are wired, problems in front oxygen sensor wiring harness (common) or the throttle position sensor can also cause this code to be set. Many of these sensors are replaced uneccesarily. Know also that this is a fairly involved job which will take the better part of an afternoon if you are fairly skilled. You will need to drain and refill the cooling system, and you will be disassembling a number of pipe connections that have to be reinstalled with either aftermarket gaskets or assembled with RTV, which can be tricky to get right without leaks. Here is the procedure for replacing the knock sensor on a '01 Mercury Villager: --Removal-- 1. Remove the lower intake manifold. 2. Disconnect the heater core hose from the coolant crossover tube. (refer to the diagram in the 'related links and sources' portion of this answer) Release the clamp and disconnect the hose. 3. Release the clamp and remove the lower radiator hose from the coolant crossover tube. 4. Remove the water bypass hose from the thermostat housing. Release the clamp and remove the hose. 5. Remove the coolant crossover tube. Remove the bolts and tube. 6. Remove the Knock Sensor (KS). Disconnect the electrical connector. Remove the bolt. --Installation-- 1. Install the knock sensor and bolt. Connect the electrical connector. 2. Install the coolant crossover tube. Position the coolant crossover tube. Install the bolts. 3. Install the water bypass hose. Position the hose. Position the clamp. 4. Connect the lower radiator hose to the coolant crossover tube and position the clamp. 5. Connect the heater core hose to the coolant crossover tube. Connect the tube. Position the clamp. 6. Install the lower intake manifold.
How do you change the thermostat on a chevy venture?
Remove the air inlet duct tube. Remove the heat shield from the exhaust and move it out of the way. Unbolt the crossover exhaust pipe bolts from the from the front exhaust pipes move it out of the way. Unbolt the thermostat housing pipe and remove the thermostat. Installation is reverse.
Where is the orfice tube in a 2000 Ford Windstar?
It's located on a vertical aluminum tube on the firewall. Between the junction of two lines.
Where is orfice on Ford Windstar?
The orfice tube is located in the evaporator inlet tube. There is also an expansion valve in the rear evaporator case.
Where is the orifice tube located on a 2003 Ford Windstar with a 3.8 liter engine?
Follow the high-side line from the charge port to the firewall. The line breaks with a screw fitting. The orifice tube is inside the line where that fitting comes apart. It's virtually impossible to get to with the engine in the car.
Where is thermostat on 1995 Mercury Villager?
At the front of the engine under the housing that attaches to the coolant crossover tube assembly.
When did Tube Slider happen?
Tube Slider happened in 2003.
What are the release dates for Tube Slider - 2003 VG?
Tube Slider - 2003 VG was released on: USA: 18 April 2003 (Gamecube version)
