answersLogoWhite

0

Lots of vacuum lines and electrical plug ins. Good thing is theelectrical plug ins are all different, and can only go one way, on the correct fitting. You cant get them mixed up. The electrical for the 8 fuel injectors and 8 coil packs (on top of plugs) are in a loom, so you cant mess that up either. There are 10 bolts to remove to take of the plenum, 5 on each side. The back ones seem impossible to get to, but you can get all of the with a 3/8" ratchet and 6" extension. I would suggest taking the 8 coil packs off first, because there is not enough room in the back to lift straight up. You will need to do it anyway to put it back together. You will also need to take the two fuel lines off with that special tool to let the fuel rail come with the plenum. As far as vacuum lines, use a little trial and error. Not nearly as much needs to be unhooked as it first appears. Take your time, and if u feel like marking certain lines with some masking tape to indicate where it goes back to, more power to ya. Also, make some drawings on a notebook before you start, on whatever looks like a problem to you. Also, if you take parts of the right side, put them in the back of the truck on the same side, obviously, do the same on the left. Later on, you will have more hints on where things went. I.E.--a vacuum line or electrical line looks confusing, take masking tape a mark where it came off 1 and 1, 2 and 2, marking each end of the tape. TAKE YOU TIME AND DOCUMENT AND DRAW!!!!!

User Avatar

Wiki User

15y ago

What else can I help you with?

Related Questions

What is the egr valve conneted to on a 1997 v8 ford Triton engine 5.4?

Throttle body/Intake plenum assembly.


How do you Remove 1998 ford Triton exhaust manifold?

i have a 1998 ford Triton f 150 how do i remove the exhaust manifold right side


When did ford make the 4.6 Triton?

Triton is the engine in a truck , starting 1997


Ford engine with 8 cylinder?

Triton


Are ford Harley Davidson engine are Triton?

no


What Ford engine is an eight cylinder?

Triton.


How much is an engine for a Ford F-250 Triton 10 2005 if it needs to be replaced or rebuilt?

You need to replace an engine for a Ford F250 Triton 10 2005 for about $3000.


Where is the idle air control valve on a 04 f-150 5.4 Triton?

On a 2004 Ford F-150 with a 5.4 Triton engine, the idle air control (IAC) valve is located on the throttle body, which is situated on the intake manifold. It is typically mounted on the side of the throttle body and has an electrical connector attached to it. You may need to remove some components or the air intake duct for better access to the IAC valve.


Where is the camshaft sensor on a ford 5.4 Triton engine?

Under the hood


Will a 1979 ford 302 intake fit on a 1993 302 ford motor?

The intake on the 1979 Ford 302 engine is different than the intake on the 1993 Ford 302 engine. The intakes are not interchangeable.


Where is the oil sending unit on 2004 F150 Triton 5.4?

The oil sending unit on a 2004 Ford F-150 with a Triton 5.4L engine is located on the engine block, near the rear of the engine, towards the driver's side. It is typically situated above the oil filter and may require some maneuvering to access due to space constraints. You might need to remove components like the air intake or other accessories for better access.


Where is the knock sensor on a 2000 f350 Triton v10?

From what I have been told the knock sensor on a Ford Triton V10 is under the intake manifold. According to local Ford Dealer intake manifold has to be removed to replace the sensor. I am looking for diagram to see if there is another way. I will have to find engine manual to be sure and will post if I find anything new. A Pack Rat ate the wire leads off of mine.