answersLogoWhite

0

I recently removed the lower ball joint from a 91 Civic, hopefully it is the same as yours. You need a fairly large double jaw gear puller. Loosen the castle nut, but do not remove it. Place the jaws of the gear puller under the boot of the ball joint (be careful not to damage the boot). Then place the screw part of the puller on the end of the ball joint bolt and tighten the puller as tight as you possible can. Then use a blunt punch and hammer to hit on the lower arm where the bolt goes through it, it requires quite a vibration to jar the ball joint loose. Good luck.

User Avatar

Wiki User

10y ago

What else can I help you with?

Related Questions

How do you remove the radiator support in a 2000 Honda civic?

upper or lower?


How do you change a ball joints on a 2001 Honda Civic?

Honda knows they have a problem with the passenger side lower ball joint on 2001-2005 Honda civic. refer to Honda service bulletin 04-079 dated December 21,2004. the bulletin describes how to remove the ball joint and Honda now has a ball joint replacement. however, the service bulletin suggests checking the opening in the knuckle to make sure it will receive the new ball joint. the bulletin also suggest that Honda will repair it even if it is out of warranty as a good will gesture. if not, purchase the entire knuckle assembly with a ball joint from majestic Honda. it will cost you about 100 dollars .


How do you replace lower ball joint on 1996 Honda civic?

Not so easy.This is pressed into the lower control arm.So :Jack and support carRemove lower ball joint to upright nut.Separate ball joint from upright. Usually with a hammer and suspension fork.In some cases there is a spot weld that needs to be ground off in place of the snap ring.Remove the snap ring that retains the joint into the lower control arm.Use your portable ball joint and suspension press to remove and install the replacement joint.Assembly is reverse of disassembly.


1993 civic lower ball joint?

Must be pressed in. Remove steering knuckle and take it to a shop The ball joint was 25 and the shop I went to charged 75 to press it in


What is the torque specification for the lower ball joint on a 2001 Honda accord dx?

The 2001 Honda Accord lower ball joint torque specification is 90 pounds. The lower ball joint should be torqued in 45 pound intervals.


Where is the Starter 1999 Honda Civic?

Look at lower rear of engine


How do you remove a transmission from Honda Civic?

To remove the transmission from a Honda Civic, start by disconnecting the battery and draining the transmission fluid. Then, remove any components obstructing access, such as the air intake, exhaust, and driveshafts. Next, unbolt the transmission from the engine and detach the wiring harness and any fluid lines. Finally, carefully lower the transmission using a jack or transmission stand.


Where is the OBD port on a 2001 Honda Civic?

The 2001 Honda Civic OBD 2 port is on lower right edge of dash; behind console trim


How do you replace front shocks on a 1991 Honda Civic Si?

The front shocks on a 1991 Honda Civic can come off in one piece. Raise the vehicle and remove the lower suspension components. Loosen the mounting bolts in the engine bay and slide the shock out of the suspension fork. Then remove the shock from the coil and install the new shock.


How do you remove lower ball joint on 2003 GMC savana?

how to remove lower ball joint on 2003 gmc savana van


How do you replace cv joints in a 1993 Honda civic?

To replace the CV joints on a 1993 Honda Civic, first, safely lift the vehicle and remove the front wheels. Next, detach the axle nut, then remove the lower ball joint and any components obstructing the axle's removal. Slide out the old CV axle and replace it with a new one, ensuring the new axle is properly seated in the transmission. Finally, reassemble the components in reverse order, tightening all fasteners to the manufacturer's specifications.


2001 Honda Civic OBD Socket Location?

The 2001 Honda Civic OBD 2 port is on lower right edge of dash; behind console trim