0
What else can I help you with?
Can you remove a child from another state if you have joint custody?
No, you cannot move a child out of state if you have joint custody.
How do you replace a ball joint for 1997 dodge van b3500?
For the lower ball joint, remove the lower control arm and the ball joint seal. Press the ball joint from the control arm. Press the new ball joint into the lower control arm ensuring it is fully seated, install a new seal and the lower control arm.
How can a leaking threaded joint be fixed without disassembly?
One way to fix a leaking threaded joint without disassembly is to apply a sealant or thread tape to the threads of the joint. This can help create a tighter seal and prevent further leaking.
Can one person remove the other persons name from a joint checking account?
No, they cannot.
How to Remove of lower front ball joint on 01 jaguar xj8?
To remove the lower front ball joint on a 2001 Jaguar XJ8, first, safely lift and secure the vehicle, then remove the wheel. Next, detach the lower control arm from the ball joint by removing the bolts securing it. Use a ball joint separator tool or a pickle fork to separate the ball joint from the steering knuckle. Finally, remove the retaining nut and pull the ball joint from the control arm, ensuring to replace it with a new one if needed.
Name 4 types of copper tube joints?
Compression joint Soldered joint Flare joint Threaded joint
How would you replace the ball joint on your 90 accord?
I'm assuming that you are talking about the front lower ball joint as they are the most common. You remove the tire then remove the axle nut in the center of the rotor it is a should be a 32mm socket. removw the lower ball joint nut, it is a 17mm socket then with a ball hammer hit the metal casing were the ball joint goes through the lower control arm, do not hammer on the ball joint itself! it will change tone when the socket pops. when it pops pick up the assembly by the rotor and remove the lower ball joint arm from the lower control arm and remove the axle from the hub assembly. there is a retainer clip on the lower part of the ball joint that you will need to remove you will need a pair of snapring pliers for this. after removing the snapring you need to hammer the ball joint up and out of the hub. Just do these instructions backwards to install. Good luck If it's the UPPER ball joint, the whole control arm has to be replaced (the ball joint is made into the control arm, and it's non replaceable). Remove cotter pin and nut from ball joint. Get a big, heavy hammer, and hit the spindle as close to the ball joint as possible (you may have to whack it a few times). That will break the ball joint loose from the spindle. Once is loose, remove the bolts that attach the control arm to the body.
How do you change the upper control arm bushings on a 1994 gmc siera 2500 4x4?
Remove control arm from vehicle. If ball joint is pressed, use ball joint press (or hammer) to remove ball joint. If it is held in by rivits, destroy rivits and remove ball joint. Bushings may be removed and installed with ball joint press; use your head (ie: you can use a socket if there is not a ball joint press adapter that fits control arm bushing, etc.). Install new bushing STRAIGHT! Install all other parts in reverse order of removal. You should get an alignment after finished.
How do you remove a ball joint from a 2000 Nissan altima?
you need a pickle fork. use a this and a hammer to wedge the ball joint away from the control arm.
How do you replace a ball joint on a 1991 s10 blazer?
Raise this corner of the vehicle at the frame. Remove the wheel and support the lower control arm. Remove brake caliper and rotor. Unplug ABS sensor if so equipped. If T-10 (4WD) not S-10 (RWD): Remove CV axle nut at hub. Loosen upper ball joint nut. Separate upper ball joint from spindle using large hammer to knuckle or ball-joint fork. Remove upper ball joint nut, then push upper control arm up away from spindle. Loosen lower ball joint nut, then separate from spindle. Remove lower ball joint nut. If T-10: lower spindle and remove from vehicle. If S-10: raise lower control arm enough to give you working room. Use a drill or chisel or grinder to remove four rivets holding ball joint to control arm. Secure new joint to control arm using supplied hardened steel bolts and nuts and lock washers. Continue reassembly as reverse of disassembly. Align wheels, as the alignment is now incorrect.
How do you remove and replace a lower ball joint on a 1994 escort gt 1.8?
Jack up the side you want to replace and put a jack stand under it. Remove the ball joint clamp bolt and nut. Remove the bolt completely. Remove the 2 bolts holding the ball joint to the control arm and take it off.
How do you remove the lower ball joint on a 1993 gran prix?
To remove the lower ball joint on a 1993 Grand Prix, you will need to first raise and support the vehicle on jack stands. Then, you will need to remove the wheel, brake caliper, and rotor to gain access to the ball joint. Next, you will need to separate the ball joint from the control arm using a ball joint separator tool and then remove the retaining bolts from the joint to detach it from the steering knuckle. Finally, you can install the new ball joint by reversing these steps.
