answersLogoWhite

0

outside handles are riveted on. you need to drill out the rivets. you also need a rivet gun to re-install it.

REVISION: This may be on some ASTRO models, but I've never come across one with this. Most are bolted from inside the door. You simply remove the inner door panel (you may need to purchase some new plastic fasteners, as some of these will break as you pry the door panel off (most auto parts places carry them, they are fairly generic). Then, unbolt the remaining part of your broken door handle assembly and disconnect linkage and install the new one in its place. Reattach the inner door panel and you're done. The door handles on an Astro are one of the "weak links" of this vehicle. I've replaced all of them on all 3 Astro's that I've owned. The handles are readily available from a dealer (or cheaper aftermarket available on the web).

also to make it easier do not clip the lock mechanism on until it is fully installed and everything else is hooked up then get someone to turn the key while you hook up the bar and clip it makes it easier to get your hands around in there to hook up the rest of the linkage and bolts done 2 like this-easy done one the other way ouch

MY EXPERIENCE:

You will most certainly break the plastic inner door panel when removing it, there is almost no way around this. The removable fasteners are almost un-breakable and do not come off easily. What will break easily is the plastic door panel and the plastic grommet that receives the fastener so your inner panel will end up mounted only by hanging on the window ledge and by the few remaining plastic fastener mounts you didn't break - expect the inner panel to fit poorly and flop around after this job.

From the outside, the bolts that hold on the handle look like rivets but from the inside, they are threaded bolts with nuts. The lower bolt's nut can be accessed from a hole on the edge of the door frame after popping off the black plastic stopper. The upper bolt's nut is nearly impossible to access and very difficult to remove, let alone re-fasten. (Save the nuts from the original handle as the new replacement handle does not come with nuts) To make it more complicated - the upper nut requires a 7/16 wrench and the lower, a 10mm socket.

The little rod that activates the handle on the inside, pops off too easily and may break the little plastic clip that barely holds on the rod. You'll have an angry time with this little bugger.

After half a day of scraping your knuckes and cussing a lot you may be able to fit everything into place and bolt th handle back on but I guarantee you it will fit poorly and the little acuator rod will rub on the window guide so that you have to yank tha handle pretty hard to open the door. This is how my original handle shattered into pieces in the first place.

I spent some time with a wooden rod and a hammer trying to wack to window guide out of the way enough to prevent the rubbing but still the door handle does not work right.

This is a nightmare of a job. If you have the $500 or more - pay someone who knows how to do this.

or, you could try this:

I've done this a couple of times to my 1997 astro, and have learned a couple of things. IF you're not worried about appearances. take a jig saw and cut a u shaped notch in the side (not the outside or inside, the actual side of the door where the latch is). Line up the cut so that the U covers the area where the upper nut is located. I also "expanded" the hole on the bottom that's covered by the plug by doing the same thing there. After cutting the notches, bend the metal up and out of the way. You can now get a wrench on the top nut, and a socket on the bottom one . This will let you remove the outside handle without even removing the door panel. Then you replace the handle, but, as mentioned earlier, do NOT put the lock rod in until you mount the handle. Hold the handle in the open position, and put the tab end in first, otherwise you'll fight it all day. After the bolts on the new handle are tightened, use a flexible magnetic probe to put the latch rod through the bushing. Stick the probe UP through the lower hole, rest the bottom of the J of the lock rod on it, rotate it to line it up, and carefully start the lock rod through the bushing. Once it catches, carefully remove the magnet, insert a flat screwdriver through the same hole, and pop the rod through the bushing. Then bend the U cuts back into place, and you're done. Note that I've found that the silver part (where the rod attaches) does not open as far as it should on some aftermarket latches. These will quit working only a month or two after installation. To make them work longer, bend this part of the latch (you may need to carefully heat it) so that full open is about 1/4 inch further down. Be careful not to melt the bushing that holds the rod in if you do-these are impossible to find, so you'll end up spending another thirty bucks on another new latch. Also, my van is white, so I just covered the "u" cuts with a short piece of white reflective tape....improves safety and covers the hole until I need to open it again. Cutting these notches turns a two hour job into twenty minutes. Just be careful if you have power accessories, I'd pull the door panel first so I could be sure to avoid any wiring.

User Avatar

Wiki User

14y ago

What else can I help you with?

Related Questions

How do replace the rear door handle on 97 Chevy astro van?

how do you get the door open


I need driver side door handle for 1992 Chevy astro?

Check the junk yards


How do you replace door handle on a Chevy Astro van?

To replace the door handle on a Chevy Astro van, first, remove the door panel by unscrewing any visible screws and gently prying off clips. Once the panel is off, disconnect any wiring attached to the power lock or window controls. Next, locate the door handle mechanism, unbolt it, and carefully detach the old handle. Install the new handle by reversing the steps, ensuring all connections are secure before reattaching the door panel.


Outer door handle installation Chevy Astro 1994?

Go to Autozone, in the HELP! section you will find replacement door handles for the Safari/Astro (they break that often) the instructions come with. This costs under $20


How do i fix a rear door handle on a 1987 Chevy Astro?

To fix the rear door handle on a 1987 Chevy Astro, first, remove the interior door panel by unscrewing any fasteners and carefully prying it off. Next, locate the handle mechanism and check for any broken parts or disconnected rods. Replace or reconnect the faulty components as needed, and then reassemble the door panel, ensuring everything is securely fastened. Finally, test the handle to ensure it operates smoothly.


How do you repair an exterior door handle on a 1988 Chevy Monte Carlo?

Should be able to access after removing interior door panel


How do you repair exterior door handle on 1992 Chevy S-10 Blazer?

Should have access after removing inner door panel


How do you replace the backdoor latch on a Chevy astro van 1997?

in my 88 astro van I had to completely break out the back handle to first get the door open then I was able to remove interior door cover to do thr replacement. in my 99 asto van I was able to remove the interior cover to open the door then replace the handle.


How do you repair inside door handle on Chevy Aveo?

To repair the inside door handle on a Chevy Aveo, first, remove the door panel by unscrewing any visible screws and carefully prying off clips. Once the panel is off, detach the handle by unscrewing or unclipping it from the door mechanism. Inspect for any broken components, and replace them if necessary, then reattach the handle and reassemble the door panel. Finally, ensure everything is securely in place and test the handle for proper operation.


How can you get a jammed driver side door lock back into the open position when the door is open on a 1998 Chevy astro van when master lock and keys and pliers don't budge it?

== == Pull on the inside door handle and it will release it so you can reset the mechanism with your fingers. This solution also worked on a Chevy Astro van 1990.


How do you repair outside door handles on the Chevy blazer 1991?

You will need to remove the door panels, and look up in the door at the handle you will see two nuts that hold the handle and a plastic clip on a rod, remove those and replace handle.


How to remove door handle 1987 Chevy?

Remove the inside door panel of your 1987 Chevy. Remove the linkage from the door handle. Remove the door handle retaining bolts. The door handle will come off.