0
unfortunatly i have done this once and am in the process of doing it again.... theres a hard way and an easy way if you get a junk yard window with the lock on it your golden! it will take 2 screw drivers and and maybe pliers. first clean out the sill that your old window was in with a flat head or small knife get every speck of glass out and try not to destroy too much rubber/foam liner or you will get wind noise! second unscrew swivel thing at the top..be careful not to strip the crappy screw like i did 2 days ago X( you may want to heat it up a bit with a hairdryer if its winter and dont lise the rubber washers! third push the bottom of the window into the metal sill...you may have to bend it open a bit but its supposed to be tight on it. clamp it tight after to make sure. fourth and final put the top swivel thing in the top hole and tighten it snug...but again dont strip it you should be done! good luck
What else can I help you with?
Replace 1996 Jeep Cherokee drivers vent window?
this is because he was a monkey this is because he was a monkey
How do you replace lock on vent window 91 Cherokee?
To replace the lock on a vent window of a 1991 Jeep Cherokee, first, remove the vent window by carefully prying off the trim and unscrewing any fasteners. Once the window is out, disconnect the old lock mechanism by removing screws or clips holding it in place. Install the new lock by securing it in the same position and reassemble the vent window. Finally, test the lock to ensure it operates smoothly before reinstalling the trim.
Jeep Cherokee vent heater only blows on defogger?
heater vent will not readjust to any position
How do you replace vent window Chevy Malibu?
How do you replace vent windowin a 2005 chevy malibu?
How do you put a the standard window latch on the vent window of a Jeep Cherokee?
if you mean how is it affixed/how to mount a new one - clean thoroughly, and use the same glue you'd use to mount a rear view to the inside fo the windsheild.
How do you replace a vent window on a Chevrolet Blazer?
A vent window on a Blazer? Wow, it must be an old one. Need to know what year you have.
How do you replace the rear vent window on a 2001 Chevy Blazer LS 4x4 2 door?
You can replace the rear vent window on a 2001 Chevy Blazer LS 4x4, 2 door with Direct Fit Power Window Regulators.
How do you change the vent doors on 1999 Jeep Grand Cherokee limited?
http://www.heatertreater.net/Grand%20CG%20dual%20motors.html
How do you replace broken 2003 Saturn Ion vent window?
To replace a broken vent window on a 2003 Saturn Ion, start by carefully removing the door panel to access the window assembly. Disconnect any electrical connectors and remove the screws or clips holding the vent window in place. Install the new vent window by reversing the removal process, ensuring it is securely fastened. Finally, reattach the door panel and test the window to ensure proper operation.
How do you replace vent window on 1982 bronco?
To replace the vent window on a 1982 Bronco, start by removing the door panel to access the window assembly. Then, carefully detach the vent window by removing the screws or bolts that secure it in place, and disconnect any weather stripping. Install the new vent window by reversing the removal process, ensuring a proper seal with new weather stripping if necessary. Finally, reattach the door panel and test the window for smooth operation.
How do you replace a vent window seal in a 1995 gmc vandura?
To replace the vent window seal in a 1995 GMC Vandura, start by removing the vent window assembly from the door. Carefully pry off any trim or molding surrounding the window to access the seal. Once the assembly is out, remove the old seal and clean the area thoroughly. Install the new seal by pressing it into the designated channel, then reassemble the vent window and trim to complete the installation.
How do you replace a vent window on a 95 GMC Vandura?
To replace a vent window on a 1995 GMC Vandura, first, remove any trim or molding surrounding the vent window. Carefully pry off the old vent window using a flat tool, ensuring not to damage the surrounding area. Clean the adhesive residue from the frame, then apply new adhesive and position the new vent window in place. Finally, press firmly, allow it to set according to the adhesive instructions, and reinstall any trim or molding.
