0
To replace the antenna wire on a 2008 Chrysler 300, first, remove the interior trim panel near the antenna base, typically located on the rear deck or roof. Disconnect the old antenna wire from the antenna and the radio unit, then route the new antenna wire through the same path. Reconnect the new wire to the antenna and the radio, ensuring all connections are secure. Finally, replace the trim panel and test the radio to ensure proper reception.
What else can I help you with?
How to replace antenna on 1992 Toyota pickup?
remove wheel and remove the plastic liner inside the fender. remove the radio and disconnect the antenna wire. Tape another, 10' long wire to the end of the antenna wire. Unscrew the nut around the antenna from on top. pull the antenna and antenna wire out through the fender. Tape the 10' long wire to the new antenna wire and pull it back through the dash to the radio.
How do you replace a fixed antenna on a 96 Honda Civic?
A fixed antenna is wired directly to the radio on a 1996 Honda Civic. Pull the center console off and find the antenna wire behind the radio. Tie a nylon to the antenna wire and pull the old unit out. Tie the new wire for the antenna to the nylon so it can be properly snaked back.
Why don't we have sound in our 1993 Chrysler 5th ave?
make sure your antenna wire from car is hooked up. stereo will have no sound until it is.
How do you remove an antenna from a '93 Nissan Sentra?
Remove the plastic cover from inside the wheel well to expose the antenna. Remove mounting bolt. To replace antenna purchase an antenna with an adapter. Cut old antenna wire at base and connect new antenna using the adapter.
What do you need to do to replace the antenna on a 1996 Ford Contour The stereo was stolen and they cut the antenna wire?
To remove antennas' you will have to unscrew the antenna from where it is currently located on the outside of the car. Usually it will have one or two types of nuts holding it in place, you will probably have to open the hood and hold the interior nut with a wrench - pull what is left of the wire through and if you have a new wire you can probably attach it to the current antenna or you could just go to a juckyard and pick on up an entire antenna and wire connected off of the same type of vehicle as yours. Reattach the antenna the same way you took it off and rethread the wire back through the firewall and plug it into the radio - most radios take a special jack on the end so you will have to replace at the very least the wire.
How do you get the antenna to go up with a new stereo installed if the antenna wire is connected to the stereo but the antenna won't raise now even from the switch?
The motor that raises and lowers the antenna is controlled by a wire which is connected to the power switch in the stock radio. The wire from the antenna itself has nothing to do with raising and lowering the antenna. Touch the wires that were connected to the stock radio to a hot wire and see if the antenna starts to move. If if does, hook that wire to the wire from the new radio which is supposed to control the antenna motor. If there is no such wire, connect the antenna motor wire to the Accessory circut. The antenna will go up whenever the key is turned on. Or, you can get fancy and install a switch for it.
Replace the power antenna on your 1994 sable wagon?
the power antenna is located on right front. I jacked my car, and removed the right front wheel. Then there are some small screws which are keep the inner fender plastic. unscrew them. You can reach with your hand the power antenna. Unplug the power wire, and the antenna wire, and unscrew those small (8mm) screws which are holding the antenna in its bracket.
How do you get the antenna to go up with a new stereo installed in a 1989 Mercedes 190E 2.6 if the antenna wire is connected to the stereo but the antenna won't raise now even from the switch?
The motor that raises and lowers the antenna is controlled by a wire which is connected to the power switch in the stock radio. The wire from the antenna itself has nothing to do with raising and lowering the antenna. Touch the wires that were connected to the stock radio to a hot wire and see if the antenna starts to move. If if does, hook that wire to the wire from the new radio which is supposed to control the antenna motor. If there is no such wire, connect the antenna motor wire to the Accessory circut. The antenna will go up whenever the key is turned on. Or, you can get fancy and install a switch for it.
How do you replace a car antenna wire on a 2000 Chevrolet Tracker?
If it is electric, take it off and then take it apart and install the ant.
When I use the radio on 2001 C320 it will only pick up very local FM stations what could be the potential problems and soluions?
The antenna is disconnected, the wire is cut, or it is broken, bent, or just bad. Replace the antenna and its wire to the stereo in the dash.
How do you replace a 1994 Honda Prelude antenna?
You would need to get a tool to remove the notched chrome piece that holds the antenna mast, or carefully use pliers to unscrew it out. After you remove that, the antenna itself is held by a 10mm bolt. to get to it you'll need to open up the trunk lining near the antenna location and remove that bolt. Then, pull the antenna far enough to disconnect the antenna wire and power. Assuming the antenna motor is still functional, you can then replace the antenna mast with a new one. Or, you can install an aftermarket rubber antenna.
Can you replace an XM radio antenna with any other antenna like a 3ft hard cb antenna?
You can replace an XM radio antenna with a CB antenna, a ham 40-meter mobile antenna, a cellphone antenna, a GPS antenna, a TV antenna, a wire coat hanger, a 6 GHz microwave antenna, or a chain of paperclips. However, since none of them is optimized to operate at the frequencies of XM radio, like the XM antenna is, none of the others will work as well. Most of them will likely be so inefficient at the satellite radio frequencies that when you use one of those, you hear nothing at all on your radio.
