0
Answer
THIS BULLETIN SUPERCEDES TECHNICAL SERVICE BULLETIN 23-11-95, DATED
MARCH 10, 1995, WHICH SHOULD BE REMOVED FROM YOUR FILES AND NOTED
IN THE 1995 TECHNICAL SERVICE BULLETIN MANUAL (PUBLICATION NO.
81-699-96084). ALL REVISIONS ARE HIGHLIGHTED WITH **ASTERISKS** AND
INCLUDE ADDITIONAL MODEL YEARS AND PART NUMBER CHANGE.
SUBJECT:
Door Glass Lift Plate Service
OVERVIEW:
This bulletin involves replacing door glass lift plates.
MODELS:
1993 - **2001** (LH) Concorde/Intrepid/LHS/
New Yorker/Vision/300M
DISCUSSION:
Door glass lift plates are now serviced separately from the glass. Anytime the door glass is
intact and the lift plate(s) is worn or damaged, perform the repair procedure.
PARTS REQUIRED:
AR(2) **04878907AA** Lift Plate, Door Glass
AR NPN Urethane Windshield Sealer (3M p/n
08609 or Equivalent)
REPAIR PROCEDURE:
THIS REPAIR IS COMPATIBLE WITH DAIMLERCHRYSLER'S MOBILE
SERVICE PROGRAM AND DOES NOT REQUIRE HOISTS OR OTHER
FULL SERVICE FACILITY SPECIAL EQUIPMENT.
1. Remove door trim panel and upper trim retainer channel.
2. Connect power window switch and lower window to 50 mm (2 in.)
3. Loosen screws holding regulator roller channel to glass.
4. Slide roller channel rearward to allow screw heads to pass through key slots in channel.
5. Separate glass from roller channel.
6. Raise glass upward and out of opening at top of door.
7. Mark location of liftplate(s) on glass.
8. Heat lift plate with propane torch or heat gun to soften urethane and pry lift plate from
glass by inserting flat screw driver between edge of glass and plate.
23-039-00 -2-
9. Clean any remaining urethane from glass surface.
10. Apply urethane windshield sealer to channel in new lift plate.
11. Push and/or tap plate onto glass in the previously marked position.
12. Allow urethane to harden for at least 12 hours before operating window (longer times are
required if temperature is below 50 degrees F.).
NOTE: URETHANE SHOULD SET FOR 1 HOUR BEFORE HANDLING/INSTALLING
THE GLASS. THE REMAINING CURE TIME CAN BE ACHIEVED IF THE WINDOW IS
INSTALLED AND LOCKED IN THE UP POSITION FOR THE SPECIFIED TIME. THIS
WILL ALLOW THE VEHICLE TO BE RETURNED TO THE CUSTOMER WITH THE
WINDOW HANDLE OR SWITCH TAPED TO PREVENT USE.
13. Reverse removal instructions to install glass in door.
What else can I help you with?
How do you remove the window crank on a 1998 dodge neon?
Pull out the U-clip located on the base of the window crank.
How do you replace manual window crank on a 97 dodge neon?
remove the clip retaining crank to the regulator shaft, this requires a special tool available at most parts houses.
How do you you remove the manual window handle on a 2000 Dodge Neon?
Most window handles are either held on with a screw or a clip. Your has a clip and you need a window handle removal tool to get the clip off. They are inexpensive and most auto parts stores sell them.
How do you remove the window crank on a 1999 dodge ram?
It is held on by a small wire clip on the inboard side.It is held on by a small wire clip on the inboard side.
How do you replace the rear window struts on a 1996 Chevy Blazer?
Pry up clip on ends and pull off.
How do you put up a power window that doesn't work?
Remove the door trim panel.Then clip the window regulator cables. Push window up and tape it in place until you can replace the regulator
Can you raise power window manually?
You have to disconnect the glass from the regulator or clip the regulator cables.See this post for instructionshttp://www.ricksfreeautorepairadvice.com/repair-topics/window-power-repair/replace-a-power-window-regulator
How do you change the front blinker in a 1996 Dodge Intrepid?
With the hood up look at the outer end of the Headlight, You will see what looks like a snap together piece. wiggle the corner light and this will help you to see the clip that has to be moved in order for the light to slide out so you can change the bulb...I myself just put new headlights in my 96 dodge intrepid.
How do you change the light bulb on a Dodge Intrepid?
there are two tourqu screws one on each side undo thes and slide out light then release the clip on the bulb from the back side and slide out the bulb
How do you get the dome light out of a '97 Dodge Intrepid?
pull down on both sides there is a clip on both lf and rt side I did this a week ago to change my bulbs, yes no one could answer this for me also.
How do you replace fog light bulb for 1997 Dodge Intrepid?
Remove the two screws at the top of the fog light in the front.Undo the two tabs holding the cover on to the backside of the fog light.Disconnect the wire on the bulb and remove the metal clip that holds the bulb in place.An instructional video has been included below.
How do you get window up when motor is gone in 95 aurora?
You have to disconnect the glass from the regulator or clip the regulator cables.Here's howhttp://www.ricksfreeautorepairadvice.com/repair-topics/window-power-repair/replace-a-power-window-regulator
