0
Well, assuming you've changed your oil, try disconnecting your battery, then reconnecting it. You'll lose your presets on the radio, but it should work. Otherwise, you may have a bad fuse.
XXXXXXXXXXXXXXXXXXXXX ANSWER XXXXXXXXXXXXXXXXXXXX
On a car with a computer you should NEVER disconnect the battery in an attempt to clear any lights. It will not work as you can not erase the memory. You can possibly fry a computer with the power surge of reconnecting the battery. Press the gas pedal to the floor 3 times in 5 seconds with the key "ON" and the engine off.
Reset button in the fuse box. Look in the owners manual.
What else can I help you with?
Where is the reset button on 1989 Chevrolet Suburban fuel pump?
There is none.
Where is fuel cutoff switch on 1997 Suburban?
Chevrolet does not use inertia/reset switches.
How do you reset engine light on 03 suburban?
To reset the engine light on a 2003 Chevrolet Suburban, you can use an OBD-II scanner to clear the trouble codes. Alternatively, you can disconnect the negative battery cable for about 15 minutes, then reconnect it, which may also reset the light. However, it's essential to address the underlying issue that triggered the light to ensure proper vehicle operation. Always consult a mechanic if you're unsure or if the light reappears.
Where is the fuel cut off switch on a 1999 chev suburban the one you have to reset if in an accident?
Chevrolet does not use inertia/reset switches.
How do you reset check engine light on 1990 Suburban?
To reset the check engine light on a 1990 Chevrolet Suburban, you can disconnect the vehicle's battery for about 15 minutes. This will clear the engine control module's (ECM) memory, including any stored trouble codes that triggered the light. After reconnecting the battery, start the vehicle to see if the light remains off. If the light comes back on, it may indicate that there is an underlying issue that needs to be addressed.
Reset check engine light 2002 suburban?
To reset the check engine light on a 2002 Chevrolet Suburban, you can use an OBD-II scanner to clear the trouble codes, which will turn off the light. Alternatively, you can disconnect the negative battery terminal for about 15 minutes to reset the system. However, it's important to address any underlying issues that triggered the light before resetting it to avoid potential damage to the vehicle. Always consult a professional if you're unsure about the cause or how to proceed.
How do you reset check engine light 2000 suburban?
you need a scanner
How do you reset the engine light on a 2007 suburban?
To reset the engine light on a 2007 Chevrolet Suburban, you can use an OBD-II scanner to clear the trouble codes. Simply connect the scanner to the vehicle's diagnostic port, turn on the ignition, and follow the device's instructions to erase the codes. Alternatively, you can disconnect the battery for about 15 minutes to reset the engine control module, but this may also reset other settings in the vehicle. Always ensure the underlying issue causing the check engine light is addressed before resetting it.
How do you reset brake maintenance light for a Chevy Malibu?
The instructions on how to reset the brake maintenance light in a Chevrolet Malibu can be found in the owner manual. It can be viewed for free at Chevrolet's official website.
How do you reset the check engine light on 2008 Chevrolet impalas?
After repair, you reset with a scan tool.
How do you reset change oil in 2011 silverado?
To reset the oil change light in a 2011 Chevrolet Silverado, turn the ignition to the "On" position without starting the engine. Press the accelerator pedal fully three times within five seconds. After doing this, the oil change light should reset. Turn the ignition off and then start the engine to ensure the light is no longer illuminated.
How do you turn off oil change light in a 2006 Chevrolet Colorado?
Turn ignition to auxillary pump gas pedal three times turn ignition off then back on light should be reset. also if you call jiffy lube and tell them they did not reset light they will give you process to reset.
