0
To reset the Pass lock theft deterrent system on a 2000 GMC Jimmy, follow these steps:
Insert the key into the ignition and turn it to the “ON” position (do not start the engine).
Leave the key in the “ON” position for about 10 minutes until the security light turns off.
Once the light goes off, turn the key to “OFF” for about 5 seconds.
Repeat this 3 times in total (about 30 minutes), then try to start the engine.
This reset procedure works by allowing the system to relearn your key. If your GMC Jimmy still won’t start, you may have a faulty ignition switch, key cylinder, or BCM (Body Control Module).
Need Replacement Parts?
If you're facing ongoing issues with the theft system or need quality OEM or used parts for your 2000 GMC Jimmy, visit Car Parts Store USA.
.
We specialize in affordable engines, ECUs, electrical parts, and OEM replacements, all backed by warranty and shipped across the U.S. Get a free quote today and bring your Jimmy back on the road—fast.
What else can I help you with?
How do you reset the theft deterrent system on a suzuki XL-7?
how to disable theft deterrent system on a suzuki XL-7
How do you Reset theft deterrent system on 2007 impala?
In most cases the theft deterrent system in your 2007 Chevrolet Impala will reset itself in 10 minutes. You can also remove the fuse for 10 seconds and replace it to reset the system.
The car will not start and the horn honks and lights flash; how do you reset?
wait 10 minutes for the passlock system to reset for a GM vehicle.
How do you reset theft deterrent system 2002 ford expedition?
2001
How do you reset passlock 2004 chev Colorado?
To reset the Passlock system on a 2004 Chevy Colorado, first, insert the key into the ignition and turn it to the "On" position without starting the engine. Leave it in this position for about 10 minutes until the security light turns off. After that, turn the key to the "Off" position for a few seconds, then start the engine. If done correctly, the Passlock system should be reset, allowing the vehicle to start normally.
Can you reset passkey II on a GM truck?
Passkey II can be reset based on the type of Truck you are looking at. You can usually reset it by the steps below. To determine if the passkey is your problem you need to know if the security light is flashing, solid, or out. Observe the Security indicator lamp in the instrument panel. Remove the key from the lock cylinder. - Security indicator should be Flashing when the door is open. - Security indicator should be Off when all the doors are closed. - If the Security indicator does not come On or go Off correctly, refer to the Content Theft Deterrent System diagnostic and repair information in the applicable Service Manual. With the Doors closed, place the key in the lock cylinder and turn to the Run position. Observe the Security indicator lamp. - Lamp is On and does not go Off however, the engine starts. This indicates that the Vehicle Theft Deterrent (Passlock) system detected a fault when the engine was running. - Lamp flashes On and Off. This indicates a problem has been detected by the Passlock(Passlock™) system and the engine may not start this key cycle, a current condition. If you determine that the Passlock is the issue, you need to do some web research on the "corrosion of the passlock system" GM had massive issueswith them and you may be able to get the answer there.
How do you reset a car-lok anti theft system?
Depends on the vehicle and manufacturer. On GM Passlock, you have to wait about 10 minutes for the system to automatically reset before you try it with the key again.
How do you reset passlock on a 2003 chevy impala?
To reset the Passlock system on a 2003 Chevy Impala, first, insert the key into the ignition and turn it to the "On" position without starting the engine. Leave the key in this position for about 10 minutes until the security light turns off. Then, turn the key to the "Off" position for a few seconds and repeat the process two more times. After the third cycle, the Passlock system should reset, allowing you to start the engine.
How do you reset theft-deterrent systems on 2007 Chevy Avalanche?
reset theft-deterrent systems on 2007 chevy avalanche
Where is the fuel pump reset switch 2001 GMC jimmy?
A 2001GMC Jimmy does not have a reset switch. The fuel system is computer controlled with relays.
How do you reset 1999 Chevy Venture passlock?
the 1999 venture has the PK3 system for security, so you have to go to a GM dealer or a automotive locksmith that has the proper box to reset it or make a new master key for it.
How do you reset the passlock security on a 1999 Tahoe?
To reset the Passlock security system on a 1999 Tahoe, first ensure that the vehicle is in the "Off" position. Then, turn the ignition to the "On" position without starting the engine and wait for about 10 minutes until the security light turns off. Next, turn the ignition back to "Off," and then to "On" again for another 10 minutes. Repeat this process a couple of times if necessary, and the system should reset, allowing the vehicle to start.
