0
the timing is computer controlled when there is no dist.---which became standard in 1987---previous to that you rotate the dist. and set it to the number of degrees advance that the decal under the hood says---some where around 10---the timing marks are behind the harmonic balancer (which is on the end of the crankshaft)
What else can I help you with?
Where is the low level coolant sensor on a 2000 Buick Regal 38 not supercharged engine?
Coolant Recovery Reservoir. There is no sensor in the coolant recovery tank on a 1998 Buick Regal.
1998 Windstar 38 engine Where is the camshaft position sensor located?
On top of the cam sensor synchronizer which is sticking out of the top of the timing cover on the front of the engine.
Which terminal do you jump to set the timing on a 1989 Toyota pickup with a 22r-e engine?
You don't jump any terminals. I'm assuming your talking about using the DLC. Hook a timing light to the number one spark plug wire and loosen the clamp bolt on the distributor a little. Timing should be a 36-38 degrees BTD.
How to replace a starter on 1994 Buick regal coupe 38 L V6 turbo with air?
AnswerHow to replace starter for 1996 Buick Regal #.8 Liter 6cyl
Is john deere 125 bigger than a stx 38?
From everything I see the 125 is a 42" mower with a 20HP engine. The STX-38 mowers were 38" with either a 12.5 or a 13HP engine. So, yes the 125 is bigger than the STX-38.
What does the timing on a 454 mercruiser need to be set at?
I have seen specs as high as 13 degrees but that seems a bit high to me. I would settle for something around eight degrees. That way you will be reasonably safe no matter what the other conditions are. This would be setting at an idle around 650 rpm. Its a good idea to rev the engine with the timing light attached and observe maximum advance it will likely go as high as 34 degrees total from about 2600 rpm to about 3400 max. You should never exceed a total timing of more than 38 degrees.
What is the ignition timing for a gen v BBC?
The ignition timing for a Generation V Big Block Chevy (BBC) typically ranges between 32 to 38 degrees of total timing at full throttle, depending on the specific engine build and fuel used. It's essential to check the manufacturer’s specifications and consider factors such as compression ratio and camshaft profile for optimal performance. For best results, tuning on a dynamometer can help fine-tune the timing for specific applications. Always ensure to start with a conservative setting and adjust based on engine feedback.
What is the common factor for 38?
The factors of 38 are 1, 2, 19 and 38. For them to be common, they need to be compared to another set of factors.
Can i use ox-38 in car as engine oil?
No, not unless you want to destroy your engine.
How do you set the timing on 2002 Kia Rio?
This is the procedure for installing the timing belt, and contains the info on where all marks need to be set for proper timing: Install : 1.Install tensioner pulley 2.Pull tensioner pulley to its furthest point and tighten lock bolt. 3.Check that timing mark on timing belt pulley is aligned with timing mark on engine http://msw.kiausa.com/data/manual/sh...G/lc3b620a.gif 4.Check that "I" mark on intake camshaft pulley is aligned with mark on seal plate and "E" mark on exhaust camshaft pulley is aligned with mark on seal plate. http://msw.kiausa.com/data/manual/sh...G/lc3b620b.gif 5.Install timing belt onto timing belt pulley first, then idler pulley, exhaust camshaft pulley, intake camshaft pulley, and tensioner pulley in that order. 6.Check that there is no looseness in belt between idler pulley and exhaust camshaft pulley or between intake and exhaust camshaft pulleys. 7.Loosen tensioner pulley lock bolt and allow tensioner spring to apply tension to timing belt. 8.Tighten tensioner pulley lock bolt to specified torque. Tightening torque:28~38 lb-ft (38~51 N
What is the wiring schematic of a Ford 38 engine?
A wiring schematic for a ford 38 engine can be found through Ford related service manuals. The manuals depict the original factory placements of the harness and parts of the engine.
How much oil to fill a big truck engine?
38 - 46 quarts, depending on what the engine is.
