Car Computers and Sensors
Ford Windstar
Dodge Durango
Crankshaft Sensors

1998 Windstar 38 engine Where is the camshaft position sensor located?

262728

Top Answer
User Avatar
Wiki User
Answered
2006-04-05 03:54:42
2006-04-05 03:54:42

On top of the cam sensor synchronizer which is sticking out of the top of the timing cover on the front of the engine.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


The camshaft position sensor is located in the engine compartment of the 2002 Daewoo Leganza. It is at the end of the camshaft housing.

The camshaft position sensor on a 4.3L engine would be in the distributor.

The camshaft position sensor is most likely located on the cylinder head of the engine. The location could vary depending on the manufacturer.

The camshaft position sensor on your 2002 automobile is located on the front of the camshaft. You will need to remove the front engine cover to access the sensor.

The camshaft position sensor, on a Ford 6.0 liter power stroke engine, is located inside of the rear engine cover. The sensor is on the back of the camshaft.

The 2002 Ford Ranger camshaft position sensor is located on the back of the camshaft. The rear engine plate will need to be removed in order to view the sensor.

The camshaft position sensor is located on the timing chain cover at the front of the engine.

The camshaft position sensor for the 3.0L V-6 engine is located in the distributor. Good Luck!

The camshaft position sensor on a 2001 ford mustang is located on the front of the engine. It is behind the power steering fluid reservoir.

The camshaft position sensor for a Mercury Mystique is located on top of the motor. It is bolted in the same place where older versions of the engine had a distributor.

Do you have the 3.4l or 2.4l engine, the camshaft position sensor for the v6(3.4l) is located under the power steering pump

The camshaft position sensor is located under the hood, beneath the engine cover. The engine cover must be removed with a wrench to access the two sensor banks and their wiring harnesses.

The camshaft position sensor is bolted on the engine near the transmission. It is on the firewall side, and can be reached from the top.

It is located underneath the intake manifold near the rear of the engine.

I'm not sure which engine you have, but, the 2.0 has the camshaft sensor on the drivers side of the engine, right in front of the distributer

The position of the camshaft sensor on your 1997 Camaro is dependent upon the type of engine in the Camaro. In most cases the camshaft position sensor is on the back of the left-hand cylinder head.

The Camshaft Position (CMP) sensor is located on the passenger side of the engine and is accessible after removing the right front tire-2.2L engine.

according to my Haynes repair manual the camshaft position sensor for the 4.0 L OHV engine is located at the rear of the engine block, on the top of the engine block

The camshaft position sensor on a Dodge Ram 2500 5.7 engine is located at the rear of the camshaft near the top of the motor. It monitors the motion of the camshaft and constantly updates the vehicle's computer.

At the back of the engine, looks like a distributor!

It is located beneath the power steering pump in the engine block

The camshaft position sensor on a 4.6 liter engine is positioned on the side of the motor on the front of the cylinder head. A 4.6 liter engine has a camshaft position sensor on each cylinder head.

the camshaft position sensor on an 04 pt is located on the right side of the engine, towards the top (looking at it from the front), directly in back behind the oil dipstick on a non-turbo


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.