Subjects>Auto>American Cars

How hard is it to rebuild a 350 motor?

Chevyalltheway ∙

Lvl 1

∙ 14y ago

Updated: 9/16/2023

pretty simple as long as u remember how it all comes apart. label all your bolts, push rods, roller rockers, and valves and space anywhere measuser with a feeler gage. make marks on ur timing chain and sprockes. use new gaskets no matter on how new the old ones look. if u have to replace a piston replaces them all or ur engine will wear differant. if it is carb engine it will take a good weekend if u don't no what your doin if its tbi just a little longer not to much but if its a efi it sucks don't cut any wires and make sure you injectors are good.

Wiki User

∙ 14y ago

What else can I help you with?

Can you rebuild a knocking motor?

yes you can rebuild a knocking motor. its best to rebuild it from block up and it may get pricy but its worth it

Is a 1995 GMC 4 x4 1500-350 motor hard on gas?

yes

Big bear 350 hard to start runs rich just had new top end rebuild?

hopefully just a carburetor adjustment

Is a 4.8 motor the same as a 350 motor?

No. The 350, is a 5.7.

How do you rebuild 351w motor?

get a book

How hard is a 454 swap for your 350 in a 93 z71?

motor mounts are different, exhaust won't line up,

What is the engine life of a 7.3 liter power stroke motor?

With proper use and maintenance and repair I have seen 300,000 with no rebuild needed. In the f-350 ford the truck will not last this long

Will a 350 motor from a 1987 suburban swap into a 1997 suburban with a 350 motor?

no.

How much to rebuild a 1976 corvette 350 engine?

About $1700.

What is the difference in a 305 and a 350?

The 305 & 350 are basically the same engine. The 305 just has a smaller bore(3.736 vs. 4.000), not quite the power or torque, but durability should be almost identical. It is more costy to rebuild a 305 than a 350 due to the popularity of the 350. If power is not an issue then go for the 305 if you can get one cheaper. If you want more power, then a 350 is the way to go.

Which motor is bigger 302 or 350?

350

What can cause a knock in the motor of a 1997 Chevrolet 350?

Carbon build up, Bad rod bearing,main bearings low oil pressure. sounds like you need an engine rebuild.

Trending Questions

Where is the location of the Rear Thermostat for 2003 silverado? Oil capacity 1992 2.3L Ford? What is the towing capacity of a Ford F250 Super duty turbo diesel crew cab? How much horsepower on a 4 cylinder 95 ford ranger? When my 2000 4.7L auto dodge Dakota run for 2 or more hour it starts to rav up and down making jerky ride? Where is ABS relay located 2005 Chevy Blazer? Where is the fuel pump located in a 1993 f150 4x4 extended cab? Where is the coil for a 95 Mercury Cougar? Can you remove the fuel plate on a 12 valve cummins? Where is the neutral safety switch on a 84 Fiero Automatic? How much torque does the engine in the 2009 Ford F-150 have? Where is the ECM located 1991 Dodge Shadow 2.2? Why doesn't your 1989 ford ranger xlt heater get hot even though you just put in a new thermostat and it is full of antifreeze? What is the best car insurance rate in the country? Where is the crankshaft sensor on 2001 Dodge Ram 1500 3.9l? How many US employees does Nissan have? Where is the air conditioning fuse or relay on a 1987 Jeep Cherokee Chief? How do you remove a third brake light? Chevy 350 engine is leaking oil Changed all gaskets including oil pan Still leaks when you drive it Looks like leak is coming from back of oil pan What can I do to fix it? Who made the first car in america?