0
How to remove rear bumper on 1989 corvette does gas tank need to be removed first?
YOU CAN NOT REMOVE THE GAS TANK UNLESS YOU REMOVE THE BUMPER. THERE ARE NUTS LOCATED ALL THE WAY AROUND THE SEAM WHERE THE BUMPER MOUNTS UP TO THE BODY. 10MM NUTS. YOU NEED TO FOLLOW THE NUTS AND START REMOVING. YOU NEED TO REMOVE THE LISCENSE PLATE TO ACCESSS THE NUTS NEAR THAT AREA. UNHOOK ELECTRICAL TO BULBS ON THE WAY.
What else can I help you with?
How can I remove bumper stickers from my car?
Bumper stickers can be removed from a car. At first the bumper sticker should be dried with a hair drier. After one minute it can be removed. The are underneath the bumper stickers can be cleaned with water.
How do you remove the front grill on a 2007 Chevy Tahoe?
To remove the front grill on a 2007 Chevrolet Tahoe the bumper will need to be removed first. After the bumper is removed, take off the four screws and clips holding the grill in place. The grill is then ready to remove.
How do you get the bumper off a Ford Explorer?
i had to do this same thing just the other night. First at both ends of the bumper there is a supporter that has a Y at each end. first remove the bolt at the bottom of that. Then there are about 4 more bolt that connect to the frame in the center of the bumper remove those and if you removed the right bolts. it should come off.
How do you remove and replace the head lamp assembly in a 1992 Honda Accord?
first remove the bumper turn lights...two screws on one each light..then remove the lights carefully, so you do not break them.... After that...remove the bumper screws in the wheel wells.... Then, where you have removed the bumper lights...with a socket extension..and a 12 mm socket...remove two bolts on each bumper mounts.....then the bumper should come off in a forward direction.... you now have access to both headlight assemblys.
How do you remove a front bumper on a 1998 ford ranger?
To remove the front bumper on a 1998 Ford Ranger, first, disconnect the negative battery cable to ensure safety. Next, remove any plastic clips or screws securing the bumper to the fenders and the frame, typically located underneath the bumper. Once these fasteners are removed, gently pull the bumper away from the truck, taking care not to damage any wiring or attachments. Finally, if applicable, detach any fog lights or wiring connected to the bumper before fully removing it.
How do you remove front bumper from a MCI j4500 bus 1998?
To remove the front bumper from a 1998 MCI J4500 bus, first disconnect the electrical connections for any lights or sensors attached to the bumper. Then, locate and remove the bolts or screws securing the bumper to the chassis, which are typically found underneath and on the sides. After all fasteners are removed, gently pull the bumper away from the bus, being cautious not to damage any surrounding components. Ensure to have a helper if needed, as the bumper can be heavy and awkward to handle alone.
How do you remove the rear bumper on a 2004 Nissan Sentra?
To remove the rear bumper on the 2005 Nissan Sentra, you will first need to remove the rear bumper cover by using a flat tool to pry the pins. Then, access the bolts holding the bumper to the frame of the vehicle and remove the nuts. The bumper will then lift off.
How do you remove a front bumper on a 1971 Corvette?
The front bumper is pretty easy to take off, as long as the bolts arent rust fast. The first bolts to take out are the ones holding the bumper guards in place they are down under the fiberglass felance. Then unbolt the two side bolts, then unbolt the two center bolts. RJ Sottilewww.hobbycarcorvettes.net
How do you replace rear bumper 1992 300e?
First, remove the nut from the middle of the bumper, and then remove the nut from the the mounts at each rail frame. Then remove the nut or screw holding the bumper to the car at the area of the wheel. Remove the old bumper, put on the new bumper, and replace the screws in nuts in the reverse order.Ê
How do you remove bumper on 2001 Dodge Dakota?
To remove the bumper on a 2001 Dodge Dakota, first, ensure the vehicle is parked on a flat surface and the ignition is off. Begin by removing any plastic clips or screws securing the bumper cover, typically located near the wheel wells and under the front of the bumper. Next, detach the bumper by removing the bolts that connect it to the frame, usually found at the ends and possibly under the vehicle. Once all fasteners are removed, gently pull the bumper away from the vehicle.
How do you remove rear bumper from your 1993 Toyota Previa?
To remove the rear bumper from a 1993 Toyota Previa, first, ensure the vehicle is parked on a flat surface and disconnect the negative battery terminal for safety. Remove any screws or bolts located under the bumper and along the sides, which may include access through the wheel wells. Once these fasteners are removed, gently pull the bumper away from the body of the vehicle, taking care not to damage any clips or wiring. Finally, disconnect any electrical connectors if applicable before fully detaching the bumper.
How do you remove rear bumper on 1996 Hyundai excel?
To remove the rear bumper on a 1996 Hyundai Excel, first, ensure the vehicle is parked on a flat surface and disconnect the negative battery terminal for safety. Next, locate and remove the bolts securing the bumper to the chassis, typically found under the rear of the vehicle and near the wheel wells. You may also need to detach any clips or screws that hold the bumper cover in place. Once all fasteners are removed, gently pull the bumper away from the vehicle to detach it completely.
