0
If you have a 2.0L Zetec-E (Zetec): Removal Remove the accessory drive belt. Disconnect the Power Steering line from the power steering pump. Allow the fluid to drain into a suitable container. Remove the power steering pump lower retaining bolts. Disconnect the power steering pressure (PSP) switch electrical connector. Depress the locking tang. Disconnect the power steering hose from the power steering pump. Allow the fluid to drain into a suitable container. Remove the power steering pump upper retaining bolts. Raise and support the vehicle. Remove the power steering pump. Remove the PSP switch. CAUTION: Make sure vice jaw protectors are used. Secure the power steering pump in a vice. Using the special tool, remove the power steering pump pulley. Installation Using the special tool, install the power steering pump pulley. NOTE: If installing a new power steering pump, the unions that are supplied fitted to the pump should be removed and retained for future use. Using the special tool, install a new O-ring seal onto the steering gear to power steering pump union. Push the new O-ring seal onto the special tool. Locate the special tool onto the union and install the O-ring seal. Install the PSP switch. Remove the power steering pump from the vice. Install the power steering pump. Install the lower retaining bolts. Connect the power steering line. Lower the vehicle. Install the power steering pump upper retaining bolts. Connect the power steering hose to the power steering pump. Connect the PSP switch electrical connector. Install the accessory drive belt. Fill the power steering system. If you have a 2.0 SPI engine: Removal Detach the accessory drive belt from the power steering pump pulley. Using a
What else can I help you with?
How to replace a power steering hose on a 2001 Oldsmobile aurora?
how to replace the power steering hose on a 2001 oldsmobile aurora 3.5 liter engine
How do you replace a power steering pump on 2001 Oldsmobile Silhouette?
a wrench and a 12 pack
How long does it take to remove and replace a power steering pump on 2001 Ford Focus?
Replacing the power steering pump on a 2001 Ford Focus typically takes about 2 to 4 hours, depending on the mechanic's experience and the availability of tools. The process involves draining the power steering fluid, removing the serpentine belt, disconnecting hoses, and unbolting the pump. If additional issues arise, such as rusted bolts or difficulty in accessing the pump, it may take longer. Always refer to a repair manual for specific instructions and safety precautions.
How do you replace the power steering pump on a 2001 Hyundai xg300?
go to the Hyudai dealer and pay large
How do you replace water pump on a 2001 Ford Focus?
how to replace water pump on 2001 ford focus
How do you replace power steering pump on kia 2001 sportage show Images?
might want to look on youtube for that. But you just un bolt it to replace it.
How much does it cost to replace a 01 jeep liberty power steering pump?
To replace the steering pump in a 2001 Jeep Liberty, it will cost around $160. This can vary greatly depending on where you buy the part.
How do you replace power steering unit on 2001 Dodge Dakota?
To replace the power steering unit on a 2001 Dodge Dakota, first, disconnect the negative battery terminal and drain the power steering fluid. Remove the serpentine belt and disconnect the power steering pump from its mounting brackets, along with the hoses attached to it. After removing the old pump, install the new one by reconnecting the hoses and securing it in place, then refill the power steering fluid and bleed the system to remove any air. Finally, reattach the serpentine belt and reconnect the battery.
Where is the power steering fill on a 2001 Honda s2000?
The S2000 has electronic power steering hence no power steering fluid.
How do you replace the power steering pump on a 2001 Nissan Maxim 3.0?
To replace the power steering pump on a 2001 Nissan Maxima 3.0, first, disconnect the negative battery cable and drain the power steering fluid. Remove the serpentine belt, then unbolt the pump from its mounting bracket, detaching the high-pressure and low-pressure hoses. After that, install the new pump by reversing the process, ensuring all connections are secure and refill the power steering fluid before starting the engine. Finally, check for leaks and proper operation.
How do you change the power steering pump on a 2001 Honda Civic LX?
Before changing the power steering pump on a 2001 Honda Civic drain all the fluid in the system. The pump is located in the front of the engine. Remove the belt first than the pump. Unplug all hoses that travel to it and replace the unit. Once replaced flush the power steering system.
Where is the power steering sensor in a 2001 Mazda Protege?
Screwed into the side of the power steering pump.
