0
The ignition control module is mounted to the block of the engine. The coils mount to the ICM. Here's what I had to do on my 92. First remove the radiator fan. Remove the plug wires at the coils...number them if you aren't sure how they go back on. Next remove the starter....There's one bolt on the bottom bracket of the ICM that will be impossible to get to if you don't. I found it much easier to just take off all the wiring for the starter then unbolt it. It makes it much easier to pull the starter forward and down to get it out of the transmission. You'll need a 13mm socket....there's one bolt on the bottom of the bracket that you'll have to take off from under the car. Then two on the top...one on each side. Don't forget to unplug the connectors on the ICM. 2 on the passenger side, one on the driver side. Now you can remove the ICM and coils. Each coil is held on with two small screws. Remove each coil. Install is just the reverse. It sounds like a lot but it's really not that bad.
What else can I help you with?
How do you replace ignition module in a 98' Malibu?
Remove the ignition module retaining ring. Pull the ignition barrel out. Remove the wiring harness from the back of the ignition barrel. Reverse the process to install the new ignition module.
Where is the ignition module on a 1994 Mercedes Benz SL-500?
am told my ignition module on my SL 500 is faulty where can i replace this and what exactly does it do?
How do you change ignition control module 1995 Buick Riviera?
Disconnect the battery. Remove the ignition coils. Remove the ignition control module that was under the coils, and replace it.
How do you replace the Ignition Module in the Chevy Celebrity?
To replace the ignition module in your Celebrity: Unplug the wires, take note of where they go so you can put them back in the correct place. Remove the screws that hold the ignition module in place. If the old module was coated with dielectric grease on the mounting surface put fresh dielectric grease on the replacement ignition module. Put the new ignition module in place and attach with the screws. Plug the wires back in their respective places.
How do you replace ignition control module on a 1993 ford e350?
To replace the ignition control module on a 1993 Ford E350, first disconnect the negative battery cable to ensure safety. Locate the ignition control module, typically mounted near the distributor or on the firewall, and remove the electrical connectors. Unscrew the module from its mount, replace it with the new module, and reconnect the electrical connectors. Finally, reconnect the battery cable and test the ignition system to ensure proper operation.
How do you replace the ignition module on a 88 Ford Mustang?
88ford tempo
How do you replace the ignition in a 2001 Pontiac Grand Am?
ignition what? coil, swicth,module, lock cylinder? gm Jim
How do you replace the ignition module on a 1999 gmc suburban?
To replace the ignition module on a 1999 GMC Suburban, first disconnect the negative battery cable to ensure safety. Remove the distributor cap and rotor to access the ignition module, which is typically mounted on the side of the distributor. Disconnect the electrical connectors and unbolt the module from the distributor. Finally, install the new module, reassemble the distributor, and reconnect the battery.
How do you replace the ignition module on a 2002 Malibu w a 3.1L v6?
To replace the ignition module on a 2002 Malibu with a 3.1L V6, first disconnect the negative battery cable to ensure safety. Remove the engine cover if applicable, then locate the ignition module mounted on the front of the engine, usually near the ignition coil. Disconnect the wiring harness and the bolts securing the module, then carefully remove it. Install the new ignition module by reversing the removal steps, ensuring all connections are secure before reconnecting the battery.
How do you replace the ignition module on a 1993 Chevrolet Blazer?
Find your distributor cap and follow the center cable to a rectangular part. This is the ignition module. Remove it, get a new one and install it.
How do you replace the ignition module 1990 ford bronco?
To replace the ignition module on a 1990 Ford Bronco, first disconnect the negative battery cable to ensure safety. Locate the ignition module, which is typically mounted on or near the distributor; remove the screws or bolts securing it. Disconnect the wiring harness from the module, then install the new module by reversing the removal process, ensuring all connections are secure. Finally, reconnect the battery and test the ignition system to ensure proper functionality.
How do you replace the ignition switch on a 1998 Audi A6 Quattro?
2002 Audi quattro 1.8 ignition module location
