0
Fuel injectors are not opening. They open by electrical pulse from the ecu. You could have a short, a broken wire, perhaps a bad fuse or the ecu could be defective.
You also might have a bad crack sensor on the front of the engine. ECU doesn't know the position of the cylinders therefore no activity to fuel injectors etc...
What else can I help you with?
What does bo265 mean in a 01 Chevy s10?
No such code B0265. P0265 however means = Cylinder 2 Injector Circuit High.
How do you get a pressure washer to siphon soap?
Pressure washers use an attachment called a chemical injector to siphon soap into the water stream. The chemical injector works based on the the physics principle known as the Venturi Effect. The Venturi Effect occurs when there is a restriction in a medium through which water or air is flowing. This restriction causes an increase of speed in the flow, but a drop in pressure. A chemical injector uses this drop in pressure to siphon chemicals or soap into the water stream. With a chemical injector, this drop in pressure is achieved by using a nozzle with a large opening. There are two main types of chemical injectors:Downstream injector- This type of chemical injector is placed on the outlet side of the pump. A special nozzle is used (as mentioned above) to decrease the pressure to that the chemical can be siphoned.Upstream injector- This type of chemical injector is placed on the inlet side of the pump to inject the chemical into the water before it enters the pump. This type of injector is also known as a "high pressure" injector because the chemical is pumped through the pressure washer, and is thus released at the high pressures with the water. This is the only type of chemical injector that you can use different nozzles with. Since the chemical is injected using the low pressure inlet hose (garden hose), you do not need a special nozzle to decrease the pressure on the outlet side. This type of chemical injector is usually not recommended, however, due to the fact that the chemical is circulated through the pump. This can cause seals, such as the pump's o-rings, to wear out faster.
The pressure of a fully charged nitrogen cylinder is?
The pressure of a fully charged nitrogen cylinder can vary depending on the specific model and manufacturer. However, typically, the pressure of a fully charged nitrogen cylinder is around 2200 to 2500 psi (pounds per square inch). It is important to always refer to the manufacturer's specifications for accurate pressure information.
How much psi in a h cylinder?
A standard H cylinder, commonly used for industrial gases, typically holds gas at a pressure of around 2200 psi (pounds per square inch) when full. However, the exact pressure can vary depending on the type of gas contained and the specific cylinder design. Always refer to the cylinder label or manufacturer specifications for accurate pressure information.
Functions of relief valves in fluid power control systems?
Fluid power comes in two forms: hydraulic and pneumatic. The pump in an hydraulic system is a flow source, delivering a set amount of fluid every revolution. Pressure is an effect due to restriction on flow in the circuit. If the oil delivered by the pump is used to operate a cylinder, the pressure that develops is due to load on the piston. If the pressure required to move the load on the cylinder is greater than the setting of the relief valve, the piston will not move and all the oil will pass through the relief valve. Also, when the piston has moved to the end of the stroke, it cannot move any further, however the oil delivered by the pump goes over the relief valve. If there wasn't a relief valve, the pressure will build up until the oil from the pump can flow somewhere: by bursting a hose or breaking the pump or cylinder.
Where is the fuel pressure regulator on a 98 ford escort lx?
the 1998 ford escort does not have a fuel pressure regulator. It does however, have a fuel pressure sensor located on the fuel injector rail. It has a connector attached to it and can be removed by taking out the attaching screws and twisting and tugging on it.
How much pressure a LPG cylinder can take?
Typically, an LPG cylinder can handle pressure ranging from 7 to 18 bar (100 to 260 psi), depending on the specific type and design. However, it is important to always follow manufacturer's guidelines for safe handling and use of LPG cylinders.
Why it is important to be sure that there is no air in the telemotor system?
Hydraulic systems work because liquids are, for all practical purposes, incompressible. When you apply pressure to the master cylinder in a hydraulic system, that pressure is transmitted equally throughout the system.Gases, however, are extremely compressible. When you put pressure on the master cylinder in a hydraulic system in which there is air in the lines, all that happens is that you compress the air in the lines; the pressure is NOT transmitted to the working cylinders.
How do you tune up a fuel injection pump on a 2002 7.3L powerstrok?
There is no fuel injection pump the fuel pressure going to the injectors should be about 60 PSI then the injector does the rest. There is a high pressure oil pump which provides high pressure oil to the injectors however a switch monitors that and if it is low the engine will not crank or run.
What internal pressure of a cylinder with one ounce of liquid R-410A refrigerant which has been sitting in a 100 degree Fahrenheit truck is?
The internal pressure of a cylinder containing R-410A refrigerant with one ounce of liquid will depend on various factors such as the temperature-pressure relationship for R-410A and any external conditions affecting the temperature of the refrigerant. However, at 100 degrees Fahrenheit, the pressure of R-410A is approximately 228 psi.
How often should you add fuel injection cleaner to you 2002 Chevy Cavalier?
Modern fuels have a fuel injector injector cleaner built into them. However I do recommend you use a good fuel injector cleaner such as Seafoam or Chevron Techron once a year.
How many fuel injector on a ford E250 van?
The Ford E250 van typically has eight fuel injectors, as it is equipped with a V8 engine. Each cylinder in the V8 configuration has its own injector, making a total of eight. However, if the van has a different engine configuration, the number of injectors may vary accordingly. Always refer to the specific model year and engine type for accurate information.
