0
Most modern GM vehicles have a transponder in the key that prevents the starter from engaging without it. To get a new key you need to get a factory key from your dealer or an aftermarket source, then program the vehicle to accept it. Instructions on programing are generally included with the new key.
What else can I help you with?
Why wont your Oldsmobile silhouette start?
First thing for any automobile - check the battery - may be dead.
Could a 2001 Oldsmobile Silhouette not start because transmission fluid is extremely low?
The engine would start and run but it may not want to move.
Show me how to Jump-Start a 2000 Oldsmobile silhouette?
To jump-start a 2000 Oldsmobile Silhouette, first, ensure both vehicles are turned off. Connect the red (positive) jumper cable to the positive terminal of the dead battery, then attach the other end to the positive terminal of the working battery. Next, connect the black (negative) cable to the negative terminal of the working battery and attach the other end to a grounded metal surface on the dead vehicle, away from the battery. Start the working vehicle, let it run for a few minutes, and then attempt to start the Oldsmobile.
Can you use an ignition key without a chip on 2002 Oldsmobile silhouette?
No, you cannot use an ignition key without a chip on a 2002 Oldsmobile Silhouette. This vehicle is equipped with a transponder key system, which requires a key that has a chip programmed to the car to start the engine. Using a non-chipped key will not allow the ignition to engage, preventing the vehicle from starting.
Where is the negative battery terminal to jump start a Oldsmobile silhouette?
I think the negative terminal is under the fuse box to the left; you can barely get to it. However to jump from or to the Silhouette, you don't need the negative terminal. To jump the Silhouette, just attach the negative cable to metal, preferably of the engine block. To jump from the Silhouette, attach the negative cable to the large bolt about 10 inches to the right of the battery.
How do you jump a Oldsmobile silhouette?
To jump-start an Oldsmobile Silhouette, you'll need a set of jumper cables and another vehicle with a functioning battery. First, park the working vehicle close enough for the cables to reach both batteries, then connect the positive (red) cable to the positive terminal of the dead battery and the other end to the positive terminal of the good battery. Next, connect the negative (black) cable to the negative terminal of the good battery, and attach the other end to an unpainted metal surface on the engine block of the dead vehicle. Start the working vehicle, let it run for a few minutes, then attempt to start the Silhouette.
Fix power windows for an Oldsmobile silhouette?
start with replacing the switch first. check with your local junkyard first. they usually have these switches that are still good for cheap. a new motor is around 100 .
How do you reset the change engine oil light in a 2003 Oldsmobile silhouette?
To reset the change engine oil light in a 2003 Oldsmobile Silhouette, first turn the ignition key to the "On" position without starting the engine. Press the gas pedal three times within five seconds. After this, turn the ignition off, and then start the vehicle to ensure the light has reset. If the light remains on, repeat the process.
How do you fix the DVD player in a Oldsmobile silhouette?
To fix the DVD player in an Oldsmobile Silhouette, start by checking the power supply and fuses to ensure they're functioning properly. If the player doesn't respond, try resetting it by disconnecting the car battery for a few minutes. Inspect the connections and wiring for any visible damage or loose connections. If issues persist, consult the vehicle's manual or consider taking it to a professional for diagnosis and repair.
How do you replace the heater core for a Oldsmobile silhouette?
To replace the heater core in an Oldsmobile Silhouette, start by disconnecting the battery and draining the coolant. Remove the dashboard by taking out the necessary trim and screws, then detach the heater core cover. Disconnect the heater core hoses from the engine compartment and remove the old heater core. Install the new heater core, reassemble the dashboard, reconnect the hoses, refill the coolant, and reconnect the battery.
How do you replace an ignition switch on a 2001 Oldsmobile silhouette?
To replace the ignition switch on a 2001 Oldsmobile Silhouette, start by disconnecting the battery to ensure safety. Remove the steering column cover by unscrewing any screws, then disconnect the wiring harness from the old ignition switch. Unscrew the ignition switch from its mounting, replace it with the new switch, and reassemble the steering column cover. Finally, reconnect the battery and test the new ignition switch.
How do you remove the radio faceplate in a 2004 Oldsmobile silhouette premier?
To remove the radio faceplate in a 2004 Oldsmobile Silhouette Premier, start by using a flathead screwdriver or a trim removal tool to gently pry off the plastic trim surrounding the radio. Once the trim is removed, you can access the screws securing the radio unit. Unscrew these screws, then pull the radio out carefully to disconnect the wiring harness at the back. Make sure to handle all components gently to avoid damage.
