0
Two sets of bolts - small (pan itself), large (4ea, pan to tranaxle housing.
Pan bolts (small) are two lengths. The longer are across the rear. Two stage torque sequence, working center out in a crisscross pattern. Tighten all pan bolts first (first stage), then tighten again to final spec (second stage). NOTE THAT THESE ARE IN INCH-POUNDS, NOT FT-LBS
First stage - 57in-lbs
Second stage - 106in-lbs
Pan to transaxle - 4ea. Two at center, one each outer sides. Tighten center bolts first, then outer.
47ft-lbs
Good luck!
What else can I help you with?
Torque specifications for cylinder head 2003 kia Rio 1.6L?
The torque specifications for the cylinder had, in your 2003 Kia 1.6 liter engine, is 120 pounds per square inch. The bolts should be torqued at 40 pound intervals.
What is the torque spec for the cylinder head on a 2003 Saturn L300?
what the torque spec for the cylinder head on a 2003 saturn L300
What are the torque specs for front bearing assembly 2003 Saturn vue?
2003 SATURN L 300 front axle torque spec
What is the torque specs on a 2003 Chevrolete Cavalier?
Chevrolet Cavalier there are more than 100 torque specifications for your 2003 Chevrolet Cavalier. You can get a complete list of torque specifications from most Chevrolet dealerships.
What is the torque specs for brake caliper mounting bolts on a 2003 dodge ram 2500?
The torque specifications for the brake caliper mounting bolts on a 2003 Dodge Ram 2500 are typically around 25-35 ft-lbs. However, it's always a good idea to consult the vehicle's service manual or a reliable repair guide for the exact specifications, as there may be variations based on the specific braking system used. Ensure to use a torque wrench for accurate tightening to maintain proper brake function.
What are the cylinder head and crankcase torque specifications for a 2003 Polaris Indy 500?
what are the cylinder head and crankcase torque specs. for a 2003 Polaris 500
What is the torque specs for Head bolts for 2003 Johnson 4 stroke 140 hp?
What is the torque specs for Head bolts for 2003 Johnson 4 stroke 140 hp outboard boat engine
What are the torque specs for the engine of a 2003 Chevy Malibu?
The torque specifications for the engine of a 2003 Chevy Malibu can vary depending on the specific engine type. For the 3.1L V6, the cylinder head bolts typically require a torque of 65 ft-lbs, followed by an additional 90-degree turn. It's important to consult the vehicle's service manual for precise specifications and sequences, as they can differ based on the engine configuration. Always ensure to use the correct torque settings to avoid damage.
What is the full torque specs for 2003 1.6 rocam engine?
For the 2003 1.6 Rocam engine, the torque specifications typically include the following: cylinder head bolts should be torqued to 20 Nm (14.75 lb-ft) initially, followed by an additional 90 degrees. The oil pan bolts usually require a torque of around 10 Nm (7.4 lb-ft). It's essential to consult the specific service manual for your vehicle for the most accurate and detailed information, as specifications can vary slightly based on the model and production changes.
What is the torque spec for caliper bolts 2003 Chrysler pt cruiser?
The torque specification for the caliper bolts on a 2003 Chrysler PT Cruiser is typically around 25 to 30 foot-pounds (34 to 41 Nm). It's essential to use a torque wrench for accurate tightening to ensure proper installation and prevent damage. Always refer to a service manual or repair guide for confirmation, as specifications may vary based on specific models and configurations.
What are the front and rear axle nut torque specifications for a 2003 Honda XR100 motorcycle?
Front axle = 55 lbf-ft. Pinch bolts = 9 lbf-ft. Rear axle = 80 lbf-ft.
Torque specs water pump 2003 dodge ram 1500 4.7?
Hi i wannw know the torque specifications of the water pump in a 2003 dodge magnum 4.7l.Thanks,eric.
