0

Subjects>Auto>American Cars

What does the number 42 mean in the trouble codes to a 1994 Chevy suburban?

Anonymous

∙ 16y ago

Updated: 10/21/2022

Electronic Spark Timing (EST) circuit is shorted to ground.

Wiki User

∙ 16y ago

What else can I help you with?

Related Questions

How do you retrieve trouble codes for 2003 Chevy Express?

Some Haynes manuals have ECU codes

Abs trouble code Chevy?

There are several ABS trouble codes for a Chevrolet automobile. The most common ABS trouble code is; error code 628.

Can you use a jumper wire to retrieve trouble codes for 95 Chevy?

If it is OBD 1, yes.

How do you check trouble codes on a 98 Chevy astrovan 4.3 ltr vortec?

CKT range/perf

2004 Chevy Astro van trouble codes p0128?

Trouble code P0128 means:Coolant thermostat (coolant temp below thermostat regulating temp)

How do you reset indicator lights Chevy Colorado?

You must use a Diagnostic code scanner that can erase trouble codes.

Your Chevy Cavalier engine light is on?

It has set a trouble code. Have the codes pulled at a autozone or oreilly auto parts.

What kind of scanner you need for a 1995 Chevy Astro Van?

You need an OBDII scanner to retrieve the trouble codes.

How do you read codes on a 1999 Chevrolet suburban?

How to read check engine codes on a 1999 chev 1500 suburban.

How do you check trouble codes on a 1995 Chevy beretta?

To check trouble codes on a 1995 Chevy Beretta, first, locate the diagnostic connector under the dashboard near the steering column. Use a paperclip or jumper wire to connect terminals A and B on the connector. Turn the ignition key to the "On" position without starting the engine, and the check engine light will begin to flash, indicating the trouble codes. Count the flashes to determine the corresponding codes, which can then be referenced to diagnose any issues.

Why does service 4wd message come on Chevrolet suburban?

The 4wd message in a Chevy Suburban is most commonly caused by the encoder motor or the selector switch failing. The transmission computer codes should be run to see if an indicated.

How do you read diagnostic codes Chevy Suburban?

Reading diagnostic codes is easy. The driver plugs the reader/scanner into the diagnostic port of the vehicle, and the scanner/reader will give a code if there is a problem, and tell them the type of problem.

Trending Questions

How many gallons does a 2001 Ford Escape hold? Will a transmission out of a 1991 Dodge Dakota 4x4 with a 6 cylinder fit in and on a 1991 dodge Dakota 4x4 with a 8 cylinder? Why did my Upper rad hose collapse? What kind of oil should you use on your 1999 mercury mystique LS? What is a briault probe used for? Can you show me where the fuel regulator go a 1996 Chevy Truck? What kind of merchandise does Williams and Sonoma sell? 1993 5.0 ho mustang Hesitates under load only when hot? What is the illuminated wrench symbol on ford Crown Victoria dashboard? What is the firing order for a Dodge 318 5.2L or 360 5.9L and how are the plugs numbered on the block? How do you adjust a gear indicator on a 1995 Cadillac deville? How do you replace the front dash speakers on a 1997 Plymouth voyager To get at them? Where is the blower motor resistor located on a 1995 GMC Suburban? When was the first Corvette introduced? What does it mean when your ford windstar ABS light and BRAKE light or on at the same time? Where is number 4 cylinder on a 3.0 Ford Ranger 2005? How do you find an owners manual for a 1994 GMC Vandura 2500? Where is the clutch safety switch on a 91 ford F-150 4 speed? What would make the Temperature gauge is stuck on cold on a 2000 mercury cougar? Where is the fuel filter located on a 1999 Oldsmobile Alero coupe V6?

Resources

Top Categories

Product

Company

Copyright ©2025 Answers.com. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Answers.