0
It is most likely for a remote control accesssory that allows you to perform normal CD playback functions with a controller wired to the player. For example, you can sit in your chair and adjust the volume or skip songs without getting up and going to the player.
The remote wire goes to the amp. its the turn on switch from your deck to your amp. if your not running an amp, then put electrical tape around the wire , so it doesn't touch any metal and ground out.
What else can I help you with?
How do you find the remote wire in the back of your CD player of a 04 mustang?
usually the blue wire with the white stripe in any CD player
Do you need to hook up the remote wire on your car amp?
Yes a remote wire is necessary. You must wire the remote wire from the amp to and ignition source of power (a component which turns on when the ignition in the car is engaged.) i.e. the radio. The remote wire signals for the amp to power on.
How do you find the remote wire in the back of your CD player of a 98 Malibu?
Usually the remote wire is the blue wire. Although not all CD players have a remote wire. The easy way to find out if you're player has a remote wire is to go onto the manufacturer's website and check the spec's.
How do you put an amp and subwoofer in an 1996 Chevrolet pickup?
if you have aftermarket stereo it is very easy pull the stereo out of the dash and take your rca wires and plug them in to the back of the stereo and then take your blue wire which is remote wire and conect it to the remote wire on the back of the stereo, from there you rum the wires to your amp. ground the amp and hook up the sub to the amp and you are good to go. hope this helps.
Where do you hook up the remote wire for a amp in a 2008 Impala?
Get a multimeter and find any hot wire going to the stereo when key is on.
Where do you hook up the remote wire on your amp?
the rem slot on your amp to the rem trigger on your deck (blue wire on most aftermarket desks)
On the factory radio wire harness of a 2002 Oldsmobile Alero what color do you connect to the remote wire of your amplifier?
If you are unsure of the remote wire, locate your radio fuse and get a fuse connector. hook it into the fuse and run it wherever you need it. all the remote does is swith the equipment on and off.
Where do you hook up remote wire when using stock CD player?
the remote wire only needs a power source for the amp to turn on, so if u have a looped cable running from the remote input on the amp to the front of the car with a switch and then back to the power cable on the amp u can control when the amp is on just by turning the switch on or off. otherwise u will have to figure out which cable on the back of the stereo is switched power, or which cable only supplies power when the car is running. and that would require a wiring diagram.
How do i wire a toggle switch for an amp?
Hook a switch up to the remote turn on and ground. Before the wiring for the amp.
I've had a problem bypassing the factory amp in my '02 exterra to be a ble to have sound with the stereo. Any help?
Why bypass amp just get wiring diagram and hook up remote"blue wire" to the remote lead from factory amp. Or unplug amp use a meter and check which wire has power. Then turn off radio and check wire again should have no power with radio off. This will only work if factory radio is still installed. But that wire would be remote wire. Just hook up new radio remote wire to the found wire. Then connect speakers to factory plugs and use the amp.
You have a 2003 Hyundai santa fe with a monsoon CD changer what color wire would you hook up a remote wire for an amp to?
just hook it up to a wire with power when the key is turned on the same wire that turns on your stereo just change the fuse to your stereo from a 10 amp to a 15 amp
Where does the remote wire enter a kenwood CD player?
The remote wire typically enters a Kenwood CD player through the designated remote control input or terminal, which is usually located on the back of the unit. This connection allows the player to receive signals from a compatible remote control. In some models, it may also be integrated with other wiring connections, such as the power or audio outputs. Always refer to the specific user manual for your model for precise details.
