0

Subjects>Auto>American Cars

What is the torque specification on front axle lock nut on a 1995 ford explorer 4wd?

Anonymous

∙ 16y ago

Updated: 10/20/2022

On my 94 it's 35 ft lbs then back off to fit key in slot. I'm not sure about the 95 model because it's a different setup. Anybody else?

Wiki User

∙ 16y ago

What else can I help you with?

Related Questions

What are the rod and main bearing torque specs for a 1995 Toyota 4Runner 3.0 v6?

The 1995 Toyota 3.0 liter engine main bearing torque specification is 160 pounds. The rod bearings torque specification is 120 pounds.

What is the valve cover torque specification for a 1995 Dodge Dakota 3.9?

95 in-lbs.

What is the torque spec for a 1995 1.0 Geo metro spark plug?

The 1995 Geo Metro spark plug torque specification is 20 pounds. You should torque the spark plug intent pound intervals.

What are the Torque specs for 1995 Toyota thermostat housing?

The 1995 Toyota Tacoma thermostat housing torque specification is 40 pounds. The amount of torque on the thermostat housing bolts is not that important. You basically do not want to break the thermostat housing bolts.

What type of antifreeze does a 1995 Ford Explorer take?

A 1995 Ford Explorer came from the factory with a 50 / 50 mix of distilled water and GREEN color antifreeze ( meeting Ford specification ESE-M97B44-A )

What is wrong with a 1995 Ford Explorer 4wd if the front end shakes slightly when stepping on the gas but stops when you take your foot off the gas?

Have the torque convertor clutch in the trans checked out for slippiing.

Where to place the jack in the front of 99 Ford Explorer?

It should be the same as my 1995 Ford Explorer , there is a " hook " on the front of both lower control arms

Does a 1995 ford explorer have struts or shocks?

shock absorbers , front and rear

Where is no 6 spark plug located on a 1995 explorer 4.0?

On a 1995 Ford Explorer : firewall 3 - 6 2 - 5 1 - 4 front of vehicle

Head bolt torque specs 95 Pontiac sunfire?

The 1995 Pontiac sun fire cylinder had bolt torque specification is 160 pounds. The head bolts should be torqued in 40 pound intervals.

What is the torque spec for the exhaust manifold on a 95 Honda Odyssey?

The 1995 Honda Odyssey exhaust manifold bolt torque specification is 45 pounds. The exhaust manifold bolts should be torqued in 15 pound intervals.

What is the brake rotor specification for a 1995 cadillac deville?

front min spec is 30.08mm rear min spec is9mm

Trending Questions

How do you change the serpentine belt on a 2001 Chrysler town and country 3.8l? Where is the horn on a 1987 Chevy Celebrity? What is the proper procedure for filling the coolant system on a 1994 Chevy Camaro 3.4L? What is the modern day highway along the El Camino real? What years were the Chevrolet Corvette z06's made? How do you replace the air filter on a Ford Fiesta 2003? American General Finance Corporation When is your payment do? What does a pelorus jack look like? How many quarts of oil is in a 2000 Lincoln Navigator? What was the first year for the 4.0 liter engine in the Dodge Grand Caravan? What causes Jeep Compass passenger window not to roll up? Are all jeep wranglers stick shift? How do you replace a fuel pump on a 1995 Chevy silveroado ext cab? Where is the the ac drain on a dodge stratus? Ford Taurus fishtail when hitting a bump or dip in road? Do you have to reset the computer after changing an ignition coil on a 99 Firebird? Why Chev 350 running with timing 6 to 8 deg after top dead center? How do you remove the headlight in a 1995 dodge caravan? Where is the starter located on a 1993 Buick Lesabre? Does a 2001 Yukon have rear brake rotors?

Resources

Top Categories

Product

Company

Copyright ©2025 Answers.com. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Answers.