0
The tow capacity of a 2009 Pontiac Montana SV6 is approximately 3,500 pounds when properly equipped. This capacity can vary based on factors such as the vehicle's configuration and the load distribution. It's important to consult the owner's manual or a dealer for specific towing guidelines and recommendations to ensure safe towing practices.
What else can I help you with?
Cylinder Torque sequence 2000 Pontiac Montana SV6?
What is the Cylinder Torque sequence 2000 Pontiac Montana 3.4V6
IPontiac Montana sv6 ending production?
2009 models are supposed to be the last year of production
What causes Reduced Engine Power on 2005 Pontiac Montana SV6?
Reduced engine power, on your 2005 Pontiac Montana, can because by several things. The most common cause of reduced power is a lack of fuel.
Why does your Pontiac Montana sv6 has a rough idle?
yes mine had a really rough idle and it turns out the motor mount needed replacing
Where is the instrument panel fuse block located in a Montana sv6?
a picture of where it is and to get to it
Where can one purchase a 2006 SV6?
One can purchase a 2006 Pontiac Montana SV6 at their local used car dealership. Alternately, one can purchase this vehicle by looking for owners who are selling this vehicle in the newspaper, or by word of mouth. One can also check online resources for used car sellers.
How much torque should you use on a 2006 Pontiac Montana sv6 when installing calipers?
When installing calipers on a 2006 Pontiac Montana SV6, you should use a torque specification of approximately 75 lb-ft for the caliper mounting bolts. It's crucial to follow the manufacturer's specifications and use a torque wrench to ensure proper installation and prevent damage. Always double-check the specifications in the vehicle's service manual, as they may vary based on specific models or configurations.
How do you change rear brake pads a d rotors on a 2008 Montana sv6?
How do you change the rear brakes on a 2008 Montana
What is the firing order for a 2005 Pontiac Montana?
The firing order for a 2005 Pontiac Montana (applies to both the 3.4L Montana and 3.5L Montana SV6) is: 1-2-3-4-5-6 The front cylinder head bank contains cylinders 2-4-6. The rear bank contains cylinders 1-3-5. Behind the rear bank are the three ignition coils. They are lined up from left to right: 5-2 / 3-6 / 4-1.
How many liters of oil does a 2007 Montana SV6 with a 3900 engine hold?
engine oil with filter 4.0qt 3.8L
Are the body parts of a 2001 Pontiac Montana interchangeable with any other years or models?
For the most part, yes. a 2001 Montana will be compatible with Chevrolet Venture ('97-'05), Oldsmobile Silhouette ('97-2004) and Pontiac Montana/Pontiac Trans Sport ('97-05) Also, if you're going to a junk yard for parts, keep an eye out for Buick Terraza, Saturn Relay, Chevrolet Uplander & Pontiac Montana SV6. These models range from year 2005 to 2010 (Not sure what year Buick & Saturn ceased production) Many parts are interchangeable with your 2001, with the exception of the rear tail light, front fenders, hood and nose clip assembly For example, the power sliding door from a Buick Terazza year 2008 will easily fit and work with your 2001 Pontiac Montana. Hope this helps.
What do you need to hook up a trailer with a 7 pin set up to your 2006 Pontiac Montana sv6?
you shouldn't. You will need to buy a "simple plug in" style. it will have a built in device that isolates your cars computer from backfeed. 7pins are used with RV's. the seventh pin is for electric brakes. therefore you will not need a seven pin. if one is not offered at a napa it'll be a dealer item
