0
What tools do you need to change the drive belt on a 1999 Ford F150 truck and how do you do it?
----------------------------------------------------------------------------------
Serpentine Belt
Under the hood should be a diagram of the belt, this is your best reference without the service manual. All you have to determine is which direction to rotate the belt tensioner, and then put the belt back on as shown in the diagram.
If it is not you can run down to your nearest auto parts store and they can print it out for you or just buy the Hayes or chilton manual on your car. It only cost a few bucks and it well helps you out later down the line if something else brakes.
Relieve Serpentine Belt Tension.
Before removing the belt, note its routing around all applicable pulleys for ease of installation.
1. Using a box end wrench on the tensioner pulley center bolt, rotate the tensioner assembly clockwise.
2. While holding the tensioner in this position, remove the alternator drive belt from one or two of the applicable pulleys.
Use a box end wrench to rotate the tensioner pulley assembly clockwise to relieve serpentine belt tension
1. Slowly release the tensioner, and remove the box end wrench from the center bolt.
2. Remove the alternator drive belt from the remaining applicable pulleys.
To install:
When installing the drive belt on the pulleys, ensure that it is properly seated in all of the pulley grooves.
1. Using the box end wrench, rotate the tensioner clockwise again, then position the drive belt on all of the pulleys.
2. Slowly release the tensioner until it eliminates all drive belt slack.
3. Inspect the tensioner indicator to be sure that the belt is properly tensioned. If the belt tension is incorrect, the belt should be replaced with a new one, or, if installing a new belt, the belt may not be the correct belt for your vehicle.
4. Then start the engine. Ensure that the drive belt works properly.
5. Stop the engine, then double-check to ensure that the belt is properly seated on all applicable pulleys.
What else can I help you with?
Why do you have to put your truck 1999 ford f150 in drive to get the wipers to come on or put it in park to change the speed?
Sounds like broken wires in the multi function switch ..
How do you change a cabin filter on a 1999 dodge truck?
It doesn't have one.
Do you need a special tool to remove the differential on a 1999 dodge 4x4 truck?
Yes, there are a couple of special tools needed.
Can you use a 1999 two wheel drive dodge transmission in a 2000 dodge four wheel drive truck?
Only you swap the overdrive/tailshaft unit.
How do you change the heater core on a 1999 Chevy 4 wheel drive?
To change the heater core on a 1999 Chevy 4-wheel drive, first remove the dashboard and drain the coolant. Unbolt the core from its mounts and remove the dash panel to be able to change the heater core.
Will a 1999 silverado truck engine fit in a 1993 silverado truck?
Yes it will but you will have to change the computer and the wiring harness to make the engine run. You will also have to change the fuel pump that is inside of the gas tank. Alot of work to make that year engine work in the 93 truck.
Will a 1992 Dakota truck motor fit into a Dodge truck 1999 Dakota?
Will a 1992 Dakota truck motor fit into a dodge truck 1999 Dakota?"
How do you change an odometer cable on a 1999 Ford Ranger 4-wheel drive?
its electronic. No cable
1999 dodge truck 4wheel drive abs and brake lights are on after changing brakes what will cause this?
You need to have the abs checked for codes. Then you can diagnose cause.
When was Truck Records created?
Truck Records was created in 1999.
What does it take to convert a 1999 Dodge Dakota 2 wheel drive to a 4 wheel drive?
You need a different front end, transmission, transfer case, wiring, etc. Buy a different truck.
How do you change a 1999 2 wheel drive to a 4 wheel drive?
You need to exchange the front axle, transfer case, and the transmission to change a 1992 2-wheel drive to a 4-wheel drive. It is not an easy project and will require a lot of time and effort.
