0
I just replaced the crankshaft position locator (crank sensor) on my 89 Cutlass Supreme SL. Although I don't know if this will help since mine was a 2.8 L V6 (Eng Code W), but mine was located between the oil pan and transmission pan on the backside of the engine, just above the oil pan. In other words, its between the engine and the firewall on the bottom side.
You have to crawl under the car..... BE SURE TO USE JACK STANDS AND DONT TRUST JUST A JACK. It required a 5/16 closed end wrench. Use the closed end wrench to avoid stripping the bolt head. Its very tight in there. I dropped that wrench on my face at least 20 times. Once you get the one bolt unbolted, GENTLY pry it out with a very small screwdriver. Be super careful not to break it off while prying it out.
I was told if it breaks off, there is nothing you can do except knock it through and remove the oil pan to retrieve it. And you cant remove the oilpan without pulling the engine. Once I had it unbolted, it would turn, with a rag, but wouldn't pop out. It took quite a bit to get it out.
I think (so far) this has solved my problem with the car dieing and not starting for 2 hours. I also replaced the ignition module, which was also a pain but it was located on the front side of the engine.
What else can I help you with?
Where is 1996 Oldsmobile Cutlass Supreme Position Sensor Location?
where is the crank sensor located at on a 1996 cutlass ciera wit a 3.1 engine
Where is the crank sensor in a 1991 Cutlass Supreme?
Behind the harmonic balancer (dampner) that is located behind the crankshaft pulley.
Where is the crank sensor on a 3.4L 1992 cutlass supreme not the 3.1L?
It is behind the harmonic balancer.
How do you install a crankshaft sensor on a 1993 Oldsmobile Cutlass Supreme?
It takes a special gauge to install the crank sensor. It can be rented from some parts stores.
What can i do to get a 88 Oldmobile cutlass supreme to start i just had the coil packs changed what else could it be?
Check the crank sensor
Where is the crankcase sensor on a 93 Oldsmoble Cutlass Supreme?
If you are referring to the Crankshaft sensor, or crank angle sensor it is located on the passenger side of the engine compartment near the harmonic balancer. (For the 3.1 L) I have a 95 with a 3.1L and it had intermitant missing and starting problems. I replaced the crank position sensor (which was located behind the harmonic balancer) and the camshaft position sensor (located under the power steering pump) and it corrected the problem.
Where is the crank sensor on 1991 olds cutlass ciera?
the crank sensor is behind the harmonic balancer
Where is the crank sensor located on a 1992 Oldsmobile Cutlass Supreme?
It's on the back of the engine....and hell to get to. Better off taking to a garage. I just broke mine off. Now I have to drop the oil pan and drive it back out.
94 olds cutlass supreme will not crank?
i had same problem on my 94 cutlass supreme...long story short, it was the ignition switch. $300. at shop.
Location 1988 Gm Cutlass Supreme 2.8L Crank Sensor?
It is located on the rear of the motor, under the exhaust manifold. Be careful when taking it out, they have been known to break off in the hole, and then become a real pain to finish the repair..
Where a crank sensor on a 91 cutlass supreme?
It depends what engine you have but its typically on the front of the engine(th side where the belts are) and its on the front timing cover, sometimes under the crankshaft pulley,
Where can you find the crank sensor on a 93 Oldsmobile Cutlass Supreme 31?
Autozone carries this type of sensor, runs around $15AnswerIt is located behind the engine near the firewall. It's a bit tricky to get to it, you would need to rotate the engine forward. Then look under the exhaust manifold under the cylider closest to the drivers side. 10 mm deepsocket for the bolt. That's fine but I want to where it is on a 1996 Olds. Cutlass supreme.
