answersLogoWhite

0

Counterclockwise off. Clockwise on.

User Avatar

Wiki User

11y ago

What else can I help you with?

Related Questions

Remove Taurus harmonic balancer?

Remove belt,4 pulley bolts and remove pulley. Remove harmonic balancer bolt and washer,reinstall bolt with out washer,just in about half way.You will need a harmonic balancer puller.These are not very expensive about $20.00 or borrow one from somebody.You just thread the correct included bolts into the balancer where you removed the pulley bolts and will be pushing on the reinstalled balancer bolt.The balancer should clear the bolt head without the washer.This is so you don't damage the threads in the crankshaft.


How do you remove the harmonic balancer on a 2001 pt cruiser?

To remove the harmonic balancer on a 2001 PT Cruiser, first, ensure the engine is cool and disconnect the negative battery cable. Remove the serpentine belt and any components obstructing access to the balancer, such as the crankshaft pulley. Use a harmonic balancer puller tool to carefully extract the balancer from the crankshaft. Finally, ensure all bolts are removed and check for any retaining clips before pulling the balancer off.


Is crank pulley same as harmonic balancer repair?

In most cases the crank pulley bolts to the balancer so the crank pulley would not be the same as the harmonic balancer.


How do you replace the harmonic balancer on a Chevy small block?

There is a bolt in the center of it, 5/8ths inch. Remove that, then the three 9/16ths bolts in a triangle pattern, which removes the pulley. Then, you will need a harmonic balancer puller, as they are pressed on.


How do you remove a harmonic balance on a 93 Buick century?

To remove the harmonic balancer on a 1993 Buick Century, first, disconnect the battery and remove any components obstructing access, such as the serpentine belt. Next, use a harmonic balancer puller tool to carefully extract the balancer from the crankshaft. Ensure you remove any bolts securing it in place before using the puller. Finally, clean the crankshaft and inspect for damage before installing a new balancer.


How do you remove a harmonic balancer from a 92 Mazda 929?

To remove the harmonic balancer from a 1992 Mazda 929, first disconnect the negative battery cable and remove any necessary accessories obstructing access, such as the serpentine belt. Use a harmonic balancer puller tool to carefully extract the balancer by attaching it to the balancer and tightening the center bolt until it loosens. Ensure to mark the position of the balancer for proper alignment during reinstallation. Finally, check for any retaining bolts that may need to be removed before pulling it off.


Were is the crank sensor on a Pontiac grand pri?

The crankshaft position sensor is located behind the harmonic balancer. You will need a harmonic balancer puller and an impact wrench good for at least 750 ft pounds. Access the harmonic balancer through the passenger side wheel well. Remove the harmonic balancer center bolt and use the puller to remove the balancer. Use 1/4 - 28 X 3 inch bolts on the puller. The sensor is held with two screws. Be careful not to damage the weatherpack connector when releasing it from the sensor.


How do you change the harmonic balancer seal on a Toyota truck?

To change the harmonic balancer seal on a Toyota truck, first, disconnect the battery and remove any components obstructing access to the harmonic balancer, such as the serpentine belt and crankshaft pulley. Use a puller to carefully remove the harmonic balancer from the crankshaft. Replace the old seal with a new one, ensuring it's seated properly, then reassemble by reversing the removal process, tightening bolts to the manufacturer's specifications. Finally, reconnect the battery and check for leaks.


Do harmonic balancer bolts come with washers?

Harmonic balancer bolts typically do not come with washers, as they are designed to be used without them. The bolts are usually designed to provide a secure fit against the harmonic balancer and the crankshaft without the need for additional hardware. However, it's always best to consult the manufacturer's specifications or service manual for the specific vehicle to determine if washers are recommended for that application.


How do you remove the harmonic balancer on a 1990 Nissan 300ZX?

To remove the harmonic balancer on a 1990 Nissan 300ZX, first disconnect the battery and remove any accessories obstructing access, such as the fan and belts. Use a harmonic balancer puller to ensure safe removal by threading it into the balancer and turning the center bolt to pull it off the crankshaft. Be cautious to support the engine if necessary, and ensure all bolts are properly torqued during reinstallation. Finally, check for any damaged seals or components before reassembly.


How do you Remove a harmonica balancer off 94 olds 3.8?

To remove the harmonic balancer from a 1994 Oldsmobile 3.8, first disconnect the battery and remove any accessories obstructing access, such as the serpentine belt. Use a harmonic balancer puller tool to attach to the balancer and extract it by turning the center bolt, applying steady pressure. Ensure all bolts are removed and check for any retaining clips before fully detaching the balancer. Finally, clean the crankshaft before installing a new balancer if needed.


Where is the crankshaft sensor on 1995 buick regal 3.8l and how do you change it?

The crankshaft sensor is located behind the harmonic balacer. you will need a puller with special bolts to remove the balancer.