0
What else can I help you with?
How do you remove the 3.1 engine on your 1998 Pontiac Grand Prix Trying to do this out the top with the transmission attached?
Trans has to come out the bottom.
How do you replace the light bulb under the transmission shifter in a 1999 Toyota Camry?
I'm trying to find the answer for that on a 1997 Toyota Camry.
How many transmission bolts are there on a 3.4L tacoma manual transmission you are trying to pull engine and can't get the block and the transmission to separate Any tips?
There are 8 or 10 bolts (some are different lengths). Remove the gearshift lever and boot. Use a very long socket extension (2 ft) and large socket (17 or 19mm) to remove the 4 bolts at the top of the transmission. Once done the transmission will separate from the engine.
Do you have to lift both the engine and transmission when lifting the engine in a 1961 impala its a 283 with a powerglide?
If you mean lifting the engine as in removing the engine for repairs, the answer is no. You can support the transmission with a jack or blocks and remove the bolts holding the transmission and engine together. It usually is much more difficult to remove both components at the same time, due to the extra weight and trying to balance them without having to raise everything to an unsafe height. make sure you unbolt the torque converter from the flywheel. makes it that much more easier
How do you keep 1987 Nissan pickup V-6 auto transmission engine from turning over when trying to remove driveshaft nut behind pullys and does it loosen counter clockwise?
have someone step on the brake.
How do you remove the three bolts near the fire wall where the motor bolts into the transmission while trying to remove it from a 1996 jeep grand Cherokee?
u need to support the engine with a cherry picker and then remove the long motor mount bolts. after u have done that remove the engine mount brackets from the engine. then lower the engine down on to the front axle. this will give u plenty of room to reach over the head and remove the bell housing bolts. there are usually only two not three and sometimes they require a torx socket.
1989 dodge spirit transmission won't shift?
Might be the sifter cable binding. Could be transmission itself, but just check the cable by disconnecting it from the transmission and moving the shifter... If it moves then its trans, if not then just replace the cable.... My trans went out in my spirit and im trying to fight to get a trans for it, I have a guy who has one but he wants 150 and I cant afford it... But im trying.
How do you remove the floor shift knob on a 1994 Ford Ranger 2X4 pickup manual transmission?
Easy. The cap on top of the knob - with the gear arrangements on it (1,2,3,4,5,R) will pop off if you pry under it. There should be a machine screw holding the knob onto the shaft of the shifter - unscrew it, and since the knob is splined, pull the knob straight up and off. It might take a little forcing. That's all there is to it! -if you are also trying to remove the entire shifter (shaft) there is one screw at the bottom of the shaft right next to the transmission that must come out, then the shaft slides right up and off. i had to do this when dropping the tranny, in order to replace my clutch.
Where does the transmission go in a 1997 Ford Aspire?
I'm trying to find where the dip stick for transmission fluid on a 1997 Ford aspire is located
How do you remove the engine speed sensor on a 1998 ford escort?
Are you trying to disable the 106 speed limit or change what is called the Vehicle Speed Sensor? If its just switching the VSS, you have to remove the air intake, then it is the plug on top of the Transmission... Check out more info here Http://www.teamzx2.com
how to replace a transmission mount on 1985 Chevy truck?
What exactly are you trying to replace? The crossmember the transmission sits on? I have an 87, and it has a cross member under the transfer case, while the transmission just bolts to the back of the engine. If you have a 2WD model, maybe it goes under the transmission, since there's no transfer case? Anyhow, it's a simple bolt-on part... you'll need a transmission jack to hold up the transmission while you remove the cross member, and you simply unbolt it.
How do you change the clutch in a 1982 Chevrolet S-10?
The first step is to remove the transmission you can pull it all te way out or just slide it back about 2 feet to do this you will need to remove the shifter from the trans. next remove the bolts that hold the preasure plate to the flywheel the clutch disk is between these 2 items. after removing it sand the flywheel slightly then reinstall the new clutch preasure plate and always replace the throw out bearing which is located in the clutch fork . you will need to align the clutach before trying to stab the transmission back to the motor most clutch kits come with a tool to do this .
