0
Your 1994 Chevy truck needs the frame slotted before an alignment can be done Where are these frame slots that you need to knock out?
THESE SLOTS ARE LOCATED WHERE THE UPPER CONTROL ARM BOLTS TO THE FRAME. IT IS VERY HARD TO SEE THEM UNLESS YOU REMOVE THE BOLTS THAT HOLD THE UPPER CONROL ARM IN PLACE. ONCE THE BOLTS ARE OUT AND THE CONTROL ARM IS PULLED OUT OF THE WAY YOU WILL NOTICE FACTORY PRE CUT SLOTS...... BUT THE FACTORY LEAVES THE OLD SLUGS IN THE SLOT SO THE FACTORY ALLINGMENT WON'T CHANGE. UNFORTUNATLY THESES PIECES OF FRAME ARE NOT CUT ALL THE WAY OUT. THEY ARE STILL ATTACHED TO THE FRAME BY A LITTLE BIT OF METAL. THESE PIECES ARE REFERRED TO AS "KNOCK OUTS". TO GET THEM OUT USUALLY REQUIRES A SPECIAL TOOL THAT PRESSES THEM OUT. THE TOOL IS SMALL AND NOT TOO EXPENSIVE BUT CAN BE VERY FRUSTRATING TO USE. MOST ALLIGNMENT SHOP DON'T EVEN USE THEM. THEY JUST CUT IT OUT WITH A OXY ACETYLENE TORCH. IN CASE YOU HAVEN'T GOT THE IDEA ALREADY THIS JOB IS MISERABLE!!! MAKE THE ALIGMENT SHOP DO IT! ITS WORTH THE FEW EXTRA BUCKS...
What else can I help you with?
Can you knock your frame out of alignment?
yes you can knock a frame out of alignment.!!!! but is really hard!!!
Why would 2003 Chevy venture start pulling to the right?
Either because of tire pressure, bent frame, or needs an alignment.
How can I reframe a door to ensure a proper fit and alignment?
To reframe a door for proper fit and alignment, you need to measure the door opening accurately, remove the old door frame, install a new frame that fits the measurements, and adjust the frame as needed to ensure the door fits properly. Use shims to make adjustments and ensure the door is level and plumb before securing the frame in place.
What is the diffirence between a 1974 Chevy nova frame and a 1975 Chevy nova frame?
Nothing.
What newer Chevy frame will fit a 1946 Chevy truck body?
82-04 s10 frame
How do you tell if i have a bent frame on my truck?
Take it to an alignment shop.
How can I effectively frame interior wall corners to ensure structural integrity and proper alignment?
To effectively frame interior wall corners for structural integrity and proper alignment, start by measuring and cutting the studs to the correct length. Use a level to ensure the studs are plumb and square before securing them in place with nails or screws. Install blocking at the corners for additional support and stability. Finally, double-check the alignment and make any necessary adjustments before finishing the wall.
Is a 1994 Chevy silveado frame the same as a 2000 silverado frame?
no
How can I frame a garage door opening to ensure it is structurally sound and properly aligned?
To frame a garage door opening for structural soundness and proper alignment, you should use pressure-treated lumber for the frame, ensure the header is adequately supported with jack studs, and use a level to ensure the frame is plumb and square before securing it in place. Additionally, follow the manufacturer's instructions for the specific garage door you are installing to ensure proper alignment and function.
Can a frame rack be used to do a wheel alignment?
A frame rack is primarily designed for straightening vehicle frames after collisions, rather than performing wheel alignments. However, it can be part of the wheel alignment process by providing a stable platform for measuring alignment angles. For accurate wheel alignment, specialized alignment equipment, such as alignment machines with sensors, is typically required to ensure precision in adjusting the vehicle’s suspension components.
Difference between pure aloha and slotted aloha?
1) Pure Aloha is a Continuous time system whereas Slotted Aloha is discrete time system. 2) Pure ALOHA doesn't check whether the channel is busy before transmission. Slotted ALOHA send the data at the beginning of timeslot. 3) Pure aloha not divided in to time .Slotted aloha divided in to time 4) In slotted ALOHA, a frame can be sent only at fixed times, whereas in pure ALOHA, you can send any time.
Are a 2wd Chevy frame and 4wd Chevy frame the same for 88 to 99?
Yes the frames are the same. A 2-wheel drive frame is different then the 4-wheel drives.
