0
What else can I help you with?
2001 Saturn ion fuse panel?
I have a Saturn 2001 300 L . The lights on the inside of car wont work.
What is the average cost to replace a fuel pump on a 2001 Saturn?
It just cost me $735 from a mechanic I have always trusted. I have a 2001 L300.
How do you change the steering wheel lock assembly in a 2001 Saturn L200 series?
The air bag electronics are very sensitive. If you're asking this question you probably don't have the skills to be messing with the steering wheel assembly. If you mess with it the air bag can deploy causing YOU serious injury and the expense of replacing the air bag. Just take it to a professional, let them be responsible.
Can you repack a rear bearing on a 2001 dodge neon?
No, it is a sealed unit.No, it is a sealed unit.
How do you replace the wheel bearing on a 2001 ford expedition?
you first take the tire off. then you take caliper off and then the dust cover, then take the codder pin out. Unscrew the bolt and pull off rotor be carefull the front bearings are not held in by a seal so they will fall out when you take the rotor off. To take the rear seal off and get the bearing out go from the front side take something like the end of a wood hammer, stick it through the center and put on the back of the bearing. take another hammer and pound the bearing until the seal breaks loose. Take the bearing out clean all the grease out with an alchol based cleaner then take your new bearings be sure to pack them well and grease up the inside of the rotor and stick the rear bearing in tampered end down and use a block of wood and pound the new seal in and make sure it is level all the way around with the metal. then stick the front bearing in tampered end down and then put your washer on top of bearing. grease the spindle up good and put the rotor back on the spindle and make sure you break the bearing in by spinnig the rotor and tighen and loosen and tighen and loosen the nut about 4 time to break the bearings in. Make sure you put new cobber pin in and put dust cap on and caliper then put wheel back on and you are all set to go.
How do you replace a left front wheel bearing on a 2001 Saturn sc2?
To replace the left front wheel bearing on a 2001 Saturn SC2, start by safely lifting the vehicle and removing the front wheel. Next, detach the brake caliper and rotor, then remove the axle nut and disconnect the hub assembly from the steering knuckle. Use a bearing puller to extract the old bearing, clean the area, and press in the new bearing before reassembling everything in reverse order. Be sure to torque all bolts to the manufacturer's specifications and check for proper wheel alignment afterward.
Rear Wheel bearing repair on a 2001 Mazda Tribute?
The 2001 Mazda Tribute came equipped in a 2.0L L4 and 3.0L V6. The rear wheel bearing are sealed assemblies. These can be pressed in to complete the install. The OE replacement rear wheel bearings for this application are SKF #GRW266. It is recommended to replace the wheel bearings in pairs.
How do you find out which wheel bearing is bad on a 2001 Pontiac grand am gt?
how do you find out if wheel bearing is bad on a 2001 grand am gt
How do you replace front wheel bearings on a 2001 Chevy Impala?
Remove the tire and wheel from your 2001 Chevy Impala. Remove the end of the axle. Remove the wheel bearing nut. Remove the wheel bearing seal and the wheel bearing. Reverse the process to install the new front wheel bearing.
How to fix Mercury grand marquis 2001 wheel bearing?
Remove a wheel bearing on 2001grand marqus
How common does a wheel bearing go out in a Hyundai Sonata?
We lost the rear passenger side hub bearing at 90,000 miles on our 2001 Sonata. The replacement bearing ( O'Reilly's ) lasted 10,000 miles. I do not know if I damaged it during installation or if it was defective. The current bearing has gone 8,000 miles.
How do you replace the right front wheel bearing of a 2001 Nissan Maxima?
The front wheel bearing on a 2001 Nissan Maxima is replaced by removing the wheel, prying off the bearing cover, and removing the retaining pin. The retaining nut can then be taken out, the calipers removed, and the rotor pulled to allow access to the bearing.
What is the 2001 ford explorer torque specs for front wheel bearing nut?
tourqe on 2001 front wheel bearings
How do you change a front wheel bearing on a Citroen Xsara SX HDI 2001?
how u do u remove a wheel bearing on a citroen xsara
What size is the frn wheel bearing hub nut on a 2001 jimmy 4x4?
The front wheel bearing hub nut on a 2001 GMC Jimmy 4x4 typically requires a 36mm socket for removal and installation. It's important to ensure that the nut is torqued to the manufacturer's specifications after replacement. Always refer to a repair manual for specific torque settings and procedures.
Where is a Speed sensors located in a 2001 grand am?
The speed sensor is located inside the Wheel Bearing Assembly, and cannot be replaced separate from the Wheel Bearing Assy.
2001 Tracker diagram front wheel bearing?
We can't do diagrams, sorry.
