answersLogoWhite

0

What else can I help you with?

Continue Learning about Art & Architecture

How do you install red rosin paper?

Roll it out, tape the edges to subfloor. Tape each subsequent piece to previous piece.


Can red rosin paper be used for waterproofing?

No. the paper is used because it is a wicking material and will pull moisture into and out of it. It is an air barrier. It will show signs if it gets wet and then dries. It is very useful as a undercoating material in building because it wicks moisture to a broad area and allows dissipation without damage; it was often used as such over sheathing, subfloors and etc., and still is where appropriate. It is not inferior or a poor substitute for Tyvec or similar- it is a better application in many circumstances.


Why is a Car cranking but not starting?

Fuel pump gone bad? Relay stuck? Ignition module fried? Only two things will keep an engine from starting. Lack of fuel or lack of spark. The first step is to determine if spark is present by detaching a plug wire and carefully inserting a screwdriver or the like into the end and placing close enough to the engine block (metal) without touching it (1 inch or less) for a spark to jump. Have someone crank the vehicle and look for spark. If no spark then you have found the culprit. Bad coil or ignition module. CAUTION! You can get quite a jolt if you handle the wire while the car is being cranked. If you have spark then you need to determine if you have a working fuel pump. One method is to have someone turn the key from the off position to the run position (the position where the engine runs {just before the crank position}) a few times while you listen as closely to the fuel tank as you can get. You will hear the buzzing of the fuel pump if it is functioning. The other method is to locate the fuel line pressure hookup (it will be on the fuel rail. a valve not unlike a tire valve only larger) and depress the valve stem. It WILL SHOOT FUEL AT YOU. SO BE CAREFUL. Once you have done this cycle the key a few times and then depress the valve again. If it spits at you again the pump is circulating fuel, if not then the pump is not functioning. Y-THINK-Y Well i would check the spark at the plug first. You have to eliminate spark and fuel problems. If you turn the key you should hear you fuel pump engage. That doesn't necessarily mean that it's working. Once you know that the fuel is getting to the motor there are 3 things that I would check. 1. Crankshaft sensor (located on the transmission housing) 2. Camshaft indicator (located on the side of the block) 3. Ignition coil. (where all the plugs come from) The first two provide information to the PCM and if it doesn't get it the van will not start. It would help if I knew what year and model'engine size ----------------------------------------------------------------------------------- I certainly agree that these other sensors can be the cause but unfortunately to determine the source of problem beyond the simple spark or fuel tests it is best to have a diagnostic computer because there is so many little telemetric devices that will effect the computer that one could spend many, many hours and dollars replacing them one-by-one. This is when a pro should come into the picture. POST: It is my experience that an engine will not 'crank' at all if the crank sensor is bad. Y-THINK-Y


Related Questions

What is rosin core?

Rosin core is a type of solder that incorporates a rosin that is used for a flux. The rosin is in a central core of the solder and when the solder melts the rosin cleans the metal of oxides to make a strong and clean connection.


What is a multicore solder?

Solder comes in 2 basic varieties, solid and rosin-core. Simple rosin-core solder is a tube of low-melting-point metal with flux filling the single core down the center. Multicore solder has multiple hollows in it, each filled with flux.


Can i use Rosin-core solder for plumbing?

Lead free only


Can you use rosin core solder on copper?

Yes, you can use rosin core solder on copper. Rosin core solder is designed for electronics and plumbing applications, providing a good electrical connection and minimizing oxidation during the soldering process. It is important to ensure that the copper surfaces are clean and free from oxidation for optimal adhesion. Always follow appropriate safety measures and recommendations for the specific solder type you are using.


Is there a silver rosin core solder?

The number one candy holiday is halloween.


Is rosin core solder poisonous?

Rosin core solder can produce fumes containing rosin that may irritate the respiratory system if inhaled in large quantities. While rosin itself is not typically considered poisonous, it's important to use proper ventilation and safety precautions when soldering to minimize exposure to fumes.


If you cut the wires from the wire harness in a 1990 f150 what do you do to fix it?

what wires are they? If they are just regular wires like for lights or something, the best method is to solder them back together with rosin core solder and cover them with heat shrink tubing what wires are they? If they are just regular wires like for lights or something, the best method is to solder them back together with rosin core solder and cover them with heat shrink tubing


How can I effectively remove rosin from a bow?

To effectively remove rosin from a bow, use a soft cloth or brush to gently wipe the rosin residue off the bow hairs. You can also use a small amount of rubbing alcohol on a cloth to help dissolve and remove stubborn rosin buildup. Be careful not to use too much alcohol, as it can damage the bow.


How do you apply violin rosin effectively for optimal sound quality and performance?

To apply violin rosin effectively for optimal sound quality and performance, gently rub the rosin on the bow hair in a smooth and even manner. Avoid applying too much rosin, as it can create a harsh sound. It's important to regularly apply rosin to maintain a good grip on the strings and produce a clear tone while playing the violin.


How is solder produced?

Solder is a lead alloy with tin. Different mixes have different melting points, and for some work, silver is also added. Sometimes for electronic work, solder is presented in the form of a wire with several cores of rosin inside it. This was first made as a large billet of solder - the size of a pot - in which several holes were drilled and filled with rosin. The solder is then drawn out in a series of rollers in the same way that other wires are made from a billet of metal. The function of the rosin is to clean the surface of the metals to be joined, so the solder may easily adhere. For plumbing use, acid cores are used, but these should never be used in electronics. yo momma!:)


Will red rosin paper stain carpets if it gets wet?

Yes it will. I had rosin paper over a vinyl floor. It is stained pink. Mr. Clean Magic Eraser is not cleaning it and neither is anything else. Be careful!


Is solder heterogenous or homogenous?

It could be either. Any type of liquid core solder (acid core, rosin core, etc.) is heterogenous, since there's the metal part and the core part. A solid-core solder is probably homogeneous.