You cannot use share parts between these two engines because the SC is a supercharged version of the 3.8L in the LX. A supercharger is a part that adds horsepower via boost to the engine, but it works as an integrated system. This means that all of the parts on the SC's engine are specifically chosen to perform to the engine's needs, which are different than the needs in the LX version. The water pump from the LX may fit on the SC and it might work, but chances are that the LX's pump does not provide as much water flow, which would leave the engine improperly cooled and could damage the engine. You should play it safe and buy a water pump specifically made for the SC model......not true.. the part numbers are identical between the two motors. they are identical minus the forged internals and supercharger on the sc. it is not a highflow water pump on the supercoupe motor. good luck
Remove the power steering pump hose. Remove the wiring harness from the power steering pump. Remove the power steering pump retaining bolts. Reverse the process to install the new power steering pump.
Best first step is to purchase an after market repair manual. $20, They have step by step instructions with pictures. I have done this and the bolts holding the pump on, snapped off leaving the broken pieces sticking out of the block. Fortunately, my neighbour has acetylene torches and I was able, after removing coolant in block with shop vac, to heat the area around broken bolts enough to remove them. OR take it to a shop, get them to give you a price, and let them have headaches. alright this is relatively simple. and can be done with basic tools remove the 4 screws holding the pully onto the water pump then removed the serp belt by loosening the idle pully and then turning the adjustor there are 4 screws around where the pully was mounted and 2 more that are attached to a bracket that the PS pump attaches to after you have removed all 6 screws unclamp the hose leading to the firewall from the top of the pump, (follow the metal tube and youll find the hose) and unclamp the lower radiator hose from the pump. now you just have to snake the pump out and unscrew the metal tube from the top and move it over to the new pump installation is reverse except put the pully back on the pump before you put the belt back on. after the belt is back on then you have to tighten the bolts on the pully
The fuel pump on a 2005 Kia Optima is removed by the fuel tank, disconnecting the fuel lines, and pulling the wiring harness. The pump can then be unscrewed from the tank, lifted out, and a new pump put in place.
not really. to get carrot flavored water, you have to boil the water and then put pieces of carrots in.
1. Diconnect the negative battery cable 2.Drain the cooling system 3.disconnect the hoses at the pump 4.remove the drive belts 5.remove the power steering pump bracket. 6.remove the shroud and fan 7.unbolt and remove the pump. TO INSTALL 9.clean the mating surfaces thoroughly 10.using a new gasket, install the pump and tighten bolts to 13 ft. lbs. 11.reinstall all componets in reverse order. 12.after complete operate the engine with heater control valve in heat position until the thermostat opens to purge any air in system check coolant level and fill as required.
You can begin by setting the new water pump onto the 1990 Jaguar water pump platform. Tighten the water pump retaining bolts. Attached the water return hose. Put the water pump belt on. Fill the cooling system with coolant.
Can you put a 1994 thunderbird motor in a 1996 thunderbird?
There is a pipe that goes into the pump. Put the 'O' ring on the pipe and push in
Yes if you know where it is and at least a little common since
the water pump in a 2.0 engine is located behind the timing belt cover. the timing belt needs to be removed to be able to remove the pump. there are detailed instructions at www.autozone.com. they put their repair manuals on their site.
How do you put the pulley back on the power steering pump on a 1990 suburban
Hi its very easy just buy a new one take the old one out and put the new one in :)
Secure the water pump with the retaining bolts. Connect the water pump hose. Put the belt on to the water pump. Fill your cooling system with anti-freeze.
how long does it take to put a water pump in a 2002 gm sierra truck
Take your old water pump out. Take it down to your local parts store Get a new water pump and then put it in.
Secure your 1994 Toyota water pump with the retaining bolts. Connect the water pump hose. Put the water pump belt on to the water pump pulley. Fill the cooling system with anti-freeze.
If it will bolt up to the mounting holes and the pulley is the same diameter and type, yes it will work. Of course the pulleys must line up. But why would you want to go to all the trouble of changing a water pump and installing a used one? Unless it is NOS.