Splice into the seat belt wires. + - wires.
Run the wires around to your dash board. connect a 100 ohm resister to a switch as if to be parallel with the seat belt circuit. when you flip the switch the car thinks your seat belt is fastened.
The only problem when you actually want to put on your seat belt then you get some error message on the dash. So, flip the switch off then fasten your seat belt. Then your set to go.
-Check to see if there is a plug on the bottom of the seat belt harness and try that... don't know if it will work but a good idea to start with...
always try asking a junk yard too. they tear them apart and should know what does what.
NOTE: The driver and front passenger belt minder are deactivated/activated independently. When deactivating/activating one seating position, do not buckle the other position as this terminates the process.
[ol][*]Before deactivating/activating the belt minder, set the parking brake.[/ol][*]Place the transmission selector lever in PARK (P).
[ol][/ol][*]Turn the ignition switch to the OFF position.
[ol][/ol][*]Unbuckle the driver and front passenger safety belts.
[ol][*]Turn the ignition switch to the ON position (do not start the engine).[/ol][*]Wait approximately 1 minute until the safety belt warning indicator turns off.
NOTE: Step 3 must be completed within 50 seconds after the safety belt warning indicator turns off.To disable the seating position, buckle then unbuckle the safety belt 9 times, ending in the unbuckled state.[*]After Step 3, the air bag warning indicator illuminates for 3 seconds.
[ol][/ol][*]Within 10 seconds of the indicator turning on, buckle then unbuckle the safety belt.[*]This disables the belt minder feature for that seating position, if it is currently enabled. As confirmation, the air bag warning indicator flashes 4 times per second for 3 seconds.
[ul][/ul][*]This enables the belt minder feature for that seating position, if it is currently disabled. As confirmation, the air bag warning indicator flashes 4 times per second for 3 seconds, followed by 3 seconds with the light off, then followed by the air bag warning indicator flashing 4 times per second for 3 seconds again.
1. Turn ignition to Run (do not start) (seatbelt unbuckled) 2. Wait for the seatbelt light to turn off ( 1 to 2 minutes) 3. Buckle and unbuckle seatbelt 9 times 4. the seat belt light will come on for 3 seconds 5. when light goes off buckle and unbuckle seat belt 6. the light will blink and go off All Done Remember you will have to do this for both front seats.
Escape seatbelt alarm can be disabled by removing the seatbelt alarm fuse. This will disable the alarm, but it is not recommended to operate the vehicle this way.
Check owner's manual. If you don't have one copy and paste link below; www.fleet.ford.com/maintenance/owners_manuals
cut the wire to the buzzer
Disable the seat belt alarm in a e250
Get into the car, turn the key to the on position (without turning the engine on) and wait until the seat belt reminder light goes off (about a minute). Then buckle and unbuckle the seat belt 9 times within 50 seconds ending in the unbuckled position. Then the light flashes a few times real quick. Then buckle and unbuckle the seat belt within 7 seconds of the light turning off and it should be good to go. This is at least how to do it on a 2011. Just because you disable the seat belt reminder doesn't mean your not going to wear the seat belt. An adult in America is quite capable of knowing when/how to buckle up without a chime reminding them. Put your seatbelt on! It's amazing! Shuts right up! Or, you can chance having an EMT like myself pick up your body parts after you go through the windshield! Dear EMT: we have certain FREEDOMS in the U.S. Ideas or even ANSWERS to questions which you don't like ARE ALLOWED. Try not to be a NAZI
I think it is in the dashboard
Simply fastening your seat belt should put the light out. If you have a heavy object sitting on the passenger side seat like a tool box or such that could trick the light to come on. If not you have something disconnected or broken.
here you go try going here first www.ebookspdf.com/automotives/3189/ford-escape-2001-owners-manual/and if that doesnt work try what i did get in like ur going somewhere without ur seat belt on put ur key in to the on position but dont turn it on wait till the seat belt light goes off then pull ur seat belt in and out 3 times then real fast turn ur light on then off then real fast pull ur seat belt in and out again 3 times then in 5 sec. pull it back in and out then the seat belt light should flash 4 times or so if u done it right hope this help.
At the base of the pillar behind the door. One for each side. You have to remove the plastic trim.
How do you turn the seat belt buzzer off????
there should be a plug under the seat that you disconnect.
Put on your seat belt.
The easy solution is to buy extra seat belt clips that fit your seat belt mechanism from a junkyard. Put these in whenever you don't want to use the seat belt.
Use the seat belt and buckle up.
you can't, they now have sensors in the seats to detect if you are in the seat or not, it's no longer as simple as just wiring around the seat belt connector.
How do I disable seat belt alarm for a Ford F150 2004
UNDER THE DASH IS A BLACK LILTE BOX IS REALY CLOSE TO THE GAS PEDAL YUST UNPLUG
i have a 2004 Chevy col, and my chimes and seat belt make NO NOISE. the person before me took out the factory radio, and the chimes, and seat belt buzzer, ran through the radio.
Wear your seat belt, your car is trying to save your life!