Brush on latex basement paint will cote the area without problem if the tar is stable and not subject to high temperatures.
It depends on the paint and composition. An oil based mastic paint used, for example, for waterproofing a basement is not porous, however an oil based wall and trim paint is. Check the manufacturer's data sheet to be sure.
it is cool glue that you can stick stuff to!
you could probably pop the tile off with a putty knife, but you're bound to break some tiles look in the attic/basement. . .sometimes builders will leave the extra pieces there when they finish a tile job, so you might get lucky
Magilp or Megilp
Oh, dude, tempera on gesso pitch and mastic is basically just a fancy way of saying painting with egg yolk mixed with pigment on a surface prepared with gesso, resin, and tree sap. It's like the ancient version of paint and primer, but with a little extra pizzazz. So, if you ever feel like getting artsy like the old masters, now you know what to ask for at the art store!
Probably Mastic
No, asbestos containing mastic must be disposed of as construction waste.
The most effective method for using mastic remover on concrete surfaces is to apply the remover according to the manufacturer's instructions, allow it to sit for the recommended amount of time to soften the mastic, and then use a scraper or brush to remove the softened mastic. It is important to wear protective gear and work in a well-ventilated area when using mastic remover.
To effectively remove mastic from concrete surfaces, you can use a commercial adhesive remover or a heat gun to soften the mastic before scraping it off with a putty knife or scraper. Be sure to follow safety precautions and instructions on the product label.
The address of the Mastic Peninsula Historical Society is: Box 333, Mastic, NY 11950-0333
A smooth surface is needed since vinyl reflects imperfections in a surface. Grinding to get rid of high spots and concrete slobbers and a leveling material should leave you with a smooth flat substrate to work with. The MOST important preparatory event is to seal the concrete. Be sure to choose a sealer that doesn't interfere with your mastic/glue. Some sealers are not compatible and cause a loos of bond. I recommend a sealer thaT migrates into the pore structure [capillaries] of the concrete and forms a solid Inside the concrete. Not only do you have a Waterproof concrete after application, this type of product stops concrete chemistry and moisture from migrating out to a surface destroying the bond. In air conditioned space a low interior humidity will suck moisture from a slab to the interior space where it is trapped. Water collects under sheet goods, destroys the glue bond and it will cause a bubble to appear. Waterproof the concrete and you won't have these problems! Use a product that is low VOC as well so you'll have no problems with odors or chemicals. Material needs 48 hours to cure, then your ready. Rolling to get entrapped air out and get good contact is essential
IS 1195/1196 mastic with 25 mm thickness
There is little difference except mastic means 'from plant origins'.
Its called Mastic. Call a local pool distributor in your area and ask for a professional recommendation. It is a tough job that even this seasoned pool professional leaves it to people who do pool construction. Luke Pool Service, Tucker, GA
Mastic gum is mainly used for treating gastrointestinal ulcers, poor circulation, yeast infections, and breathing problems. Mastic gum seems to have little or no side effects for most people. Mastic is a part of a tree, so the only problem would be if you are allergic to certain trees, you may be allergic to Mastic Gum.
Mastic is an adhesive not a flooring some manufacturers say it can be used on floor tiles how ever I would not recommend using mastic on a floor as it would take forever to cure
When using mastic to install a tile backsplash, it is important to follow these best practices: Ensure the surface is clean and dry before applying the mastic. Use a notched trowel to spread the mastic evenly on the surface. Press the tiles firmly into the mastic, making sure they are level and aligned. Allow the mastic to dry completely before grouting the tiles. Follow the manufacturer's instructions for proper application and drying times.